Publicidad
Idiomas disponibles
Idiomas disponibles
WIDTH OF CONVECTOR
C
15.3 cm
(6 in)
Minimum
clearance to
adjacent
surface
E
15.3 cm
(6 in)
Fig. 1
model
a
b
(cm)
(cm)
QCVT-500
44.6
34.0
QCVT-1000
53.7
33.7
QCVT-1500
58.1
33.7
QCVT-2000
72.6
48.3
WALL MOUNTING INSTRUCTIONS
1. Release the mounting bracket by pressing the locking brackets on both sides.
2. Use the mounting bracket as a template by holding it against the wall as
illustrated in Fig. 1.
3. Follow the dimensions specified in Fig. 1 and place mounting bracket in the
desired location.
4. Mark the 4 screw holes. Place mounting bracket on the screw markings and ensure the
mounting bracket is perfectly level.
5. Predrill holes and insert 4 wall anchors. Wall anchors are needed for mounting on
drywall or concrete walls. Ensure you use the proper anchors for your wall type.
6. Replace the mounting bracket and fasten it with screws (minimum 4 screws).
7. Mount the convector to the mounting bracket and engage the 2 locking brackets at the
top. See Fig. 2.
Caution – high temPerature, risk of fire. keeP eleCtriCal Cords, draPery,
furnishings and other Combustibles at least 3 ft (0.9 m) away from the front
of the heater and away from the sides and rear of heater.
warning – to reduCe risk of fire, do not store or use gasoline or other
flammable vaPors and liQuids in the viCinity of the heater.
Wall bracket
Wall
Fig. 2
A
D
B
15.3 cm
(6 in)
Minimum
clearance to
adjacent
surface
E
Minimum
distance
to ground
C
d
e
(cm)
(cm)
4.5
6.2
20.8
12.2
7.8
24.8
9.8
14.6
22.2
11
13.2
22.2
Convector
ELECTRICAL WIRING
warning: this ConveCtion heater is to be used on a 240 vaC Power suPPly and
grounded outlets.
HEATER
(cm)
Caution: turn off main Power before beginning installation to avoid eleCtriC
shoCk.
WARNING: THE HEATER MUST bE INSTALLED bY A CERTIFIED
ELECTRICIAN AND IN ACCORDANCE WITH ALL LOCAL AND
NATIONAL ELECTRICAL CODES.
1. Connect white colored neutral wire (N).
2. Connect black colored live wire (L).
3. Connect green colored ground wire (G). All connections using twist on wire connectors.
Put all wires properly into the junction box before replacing the cover with the provided
screw.
OPERATION
1. Turn on the wall switch / wall thermostat to switch on the heater.
2. After switching on, the thermostat will start at the default temperature.
3. There are 3 control buttons:
UP
DOWN
°C / °F
4. In Celsius mode, pressing the UP or DOWN once will increase / decrease the tempera-
ture in 0.5°C increments. In Fahrenheit mode, press the UP or DOWN button once will
increase the temperature in 1.0°F increments.
5. Pressing the UP or DOWN buttons continuously will increase / decrease the tempera-
ture setting quickly.
6. Once the temperature control buttons are set and released, the display will change
from the temperature to the room temperature after a few seconds.
7. The LED display 3 digits. In Celsius mode, the temperature will display with one deci-
mal, e.g. 22.5; for Fahrenheit, there is no decimal, e.g. 104°F will display
as 104.
8. In the summer or whenever the convection heater will not be used for an extended
period of time, turn OFF the convector at the main switch panel (or circuit breaker).
2
LCD
THERMAL CUT-OFF
PROTECTION
SENSOR
–
Temperature up
–
Temperature down
–
Change temperature to Celsius or Fahrenheit
BLACK (L)
WHITE (N)
GREEN/YELLOW (G)
Publicidad
