Black and Decker G950 Manual De Instrucciones página 4

accessory must fit the locating
diameter of the flange. Accessories
that do not match the mounting
hardware of the power tool will run out
of balance, vibrate excessively and
may cause loss of control.
g ) Do not use a damaged accessory.
Before each use inspect the
accessory such as abrasive wheels
for chips and cracks, backing pad
for cracks, tear or excess wear,
wire brush for loose or cracked
wires. If power tool or accessory
is dropped, inspect for damage or
install an undamaged accessory.
After inspecting and installing an
accessory, position yourself and
bystanders away from the plane of
the rotating accessory and run the
power tool at maximum no-load
speed for one minute. Damaged
accessories will normally break apart
during this test time.
h ) Wear personal protective
equipment. Depending on
application, use face shield,
safety goggles or safety glasses.
As appropriate, wear dust mask,
hearing protectors, gloves
and workshop apron capable
of stopping small abrasive or
workpiece fragments. The eye
protection must be capable of
stopping flying debris generated by
various operations. The dust mask or
respirator must be capable of filtrating
particles generated by your operation.
Prolonged exposure to high intensity
noise may cause hearing loss.
i ) Keep bystanders a safe distance
away from work area. Anyone
entering the work area must wear
personal protective equipment.
Fragments of workpiece or of a
broken accessory may fly away and
cause injury beyond immediate area
of operation.
j ) Hold the power tool by insulated
gripping surfaces only, when
performing an operation where
the cutting accessory may contact
hidden wiring. Cutting accessory
contacting a "live" wire may make
exposed metal parts of the power tool
"live" and could give the operator an
electric shock.
k ) Position the cord clear of the
spinning accessory. If you lose
control, the cord may be cut or
snagged and your hand or arm may
be pulled into the spinning accessory.
l ) Never lay the power tool down
until the accessory has come
to a complete stop. The spinning
accessory may grab the surface and
pull the power tool out of your control.
m ) Do not run the power tool while
carrying it at your side. Accidental
contact with the spinning accessory
could snag your clothing, pulling the
accessory into your body.
n ) Regularly clean the power tool's air
vents. The motor's fan will draw the
dust inside the housing and excessive
accumulation of powdered metal may
cause electrical hazards.
o ) Do not operate the power tool near
flammable materials. Sparks could
ignite these materials.
p ) Do not use accessories that require
liquid coolants. Using water or
other liquid coolants may result in
electrocution or shock.
q ) Do not use Type 11 (flaring
cup) wheels on this tool. Using
inappropriate accessories can result
in injury.
r ) Always use side handle. Tighten
the handle securely. The side handle
should always be used to maintain
control of the tool at all times.
s ) When starting the tool with a new
or replacement wheel, or a new or
replacement wire brush installed,
hold the tool in a well protected
area and let it run for one minute. If
the wheel has an undetected crack or
flaw, it should burst in less than one
minute. If the wire brush has loose
wires, they will be detected. Never
start the tool with a person in line with
the wheel. This includes the operator.
t ) Use of accessories not specified in
this manual is not recommended
and may be hazardous. Use of power
boosters that would cause the tool to
be driven at speeds greater than its
rated speed constitutes misuse.
u ) Use clamps or another practical
way to secure and support the
workpiece to a stable platform.
Holding the work by hand or against
your body leaves it unstable and may
lead to loss of control.
v ) Avoid bouncing the wheel or giving
it rough treatment. If this occurs,
stop the tool and inspect the wheel for
cracks or flaws.
w ) Always handle and store wheels in
a careful manner.
x ) Do not operate this tool for long
periods of time. Vibration caused by
the operating action of this tool may
cause permanent injury to fingers,
4