Cequent Performance Products 24920 Instrucciones De Instalación

Vehicle Forward
Hitch Shown In Proper Position
Equipment Required: Pull Wire, Lubricant
Fastener Kit: 24920F
Wrenches: 11/16"
Drill Bits: None
Vehicle Forward
(Driver Side)
Rear Attachment
Forward Attachment
Figure 2

Figure 3
j
Carriage Bolt 7/16 x 1-1/4" GR5
Qty. (1)

Carriage Bolt 7/16 x 1-1/2" GR5
Qty. (2)

Spacer ¼ x 7/8" x 3
Qty. (3)
m
Hex Nut 7/16" GR5
Qty. (3)
n
Conical Toothed Washer 7/16"
Qty. (3)
1. Lower exhaust by detaching it from the rubber isolators (2). Spraying lubricant on rubber isolator helps with removal.
2. Install shorter 7/16" bolt (item 1) and spacer (item 3) in passenger side frame rail (Figure 4), using the Reverse Pull wire Procedure (Figure 5).
Leave pull wire attached. NOTE: shorter bolt must be on passenger side.
3. Using the pull wire, install the forward bolt and spacer (items 2 & 3) on the driver side, leaving pull wire attached (Figure 2). Then, Reverse pull
wire the rearward bolt and spacer (items 2 & 3) on drivers side, leave the pull wire attached.
4. Place spacers (item 7) on driver side bracket, feed the pull wire end through the appropriate slots (Figure 3). Feed pull wire through slot on
passenger side.
5. Raise hitch into position, feed conical washers (item 5) through pull wire. Use conical washers to hold carriage bolts in place. Remove pull wires
and attach hex nuts. Tighten nuts to hold hitch in place.
6. Hang U-bolt around tow hook and through holes on chain plate. Put flat washer, lock washer and 3/8" nuts on. Center Hitch.
7. Tighten all fasteners to required torque specifications.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
© 2014 Cequent Performance Products, Inc
Printed in Mexico
Installation Instructions
HONDA FIT
Fascia
Drawbar Kit:
36071
Drawbar must be used in the
RISE position only.
Frame Rail
k

Tow Hook
n
m
Figure 1
Tighten all 7/16" - 14 GR5 fasteners with torque wrench to 55 Lb.-Ft. (75 N*M)
Tighten all 3/8"-16 GR5 fasteners with torque wrench to 30 Lb.-Ft. (41 N*M)
o
Chain Plate



o
U-BOLT 3/8"
Qty. (1)

Qty. (2) Spacer ¼ x 1 x 1.5

3/8" flat washer
Qty. (2)

Qty. (2) 3/8 lock washer

HEX NUT 3/8"
Qty. (2)
Sheet 1 of 3 24920N
Part Numbers:
24920
60353
77307
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 kg) Max Gross Trailer Weight
200 LB (90.8 kg) Max Tongue Weight
Accessory Rating
Wiring Access Location: PC3, 4
j

Heat Shield
n
m
Figure 4
B. Align block on
A. Insert bolt and
Access hole
Block into frame
Figure 5
Reverse Pull wiring Procedure
08-05-14
Form F206 Rev B 9-17-2012
A
Attachment
(Passenger Side)
Exhaust
C. Pull bolt thru
block
Rev. A