Descargar Imprimir esta página

Reelcraft 5000 Serie Instrucciones De Operación

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Operating Instructions
Series 5000 Spring Driven Hose Reels
Low Pressure Model Numbers:
5400 OLP118
5600 OLP118
Dimensions
INSTALLATION:
A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.
MOUNTING:
The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the
reel at the desired position and replace the screws. NOTE: For proper installation in wall mount applications, ensure
reel is mounted with inlet on the right as you are facing the reel. Failing to do so could cause latching issues.
LUBRICATION:
Hose reel spring and bearings are factory lubricated and require no further lubrication.
REPLACING HOSE: 1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to swivel joint and secure hose with clamps.
ADJUSTMENTS:
To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
REPAIRS:
Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
Reelcraft International Inc. • Ph: +44 (0) 1536 406999 • Fax: +44 (0) 1536 406777
Unit 17 - Cronin Courtyard, Weldon South Industrial Estate, Corby - Northamptonshire NN18 8AG
europe@reelcraft.com • www.reelcraft.com/europe
5450 OLP118
5635 OLP118
A
365 mm
B
356 mm
C
245 mm
D
64 mm
E
156 mm
1. Do not use reel at higher pressures or temperatures than listed on
the back of this bulletin.
2. Remove all spring tension before beginning dissassembly process.
SAFETY
Form# R831-696 Rev: 1/2016

Publicidad

loading

Resumen de contenidos para Reelcraft 5000 Serie

  • Página 1 Remove all spring tension before beginning disassembly process. Form# R831-696 Rev: 1/2016 Reelcraft International Inc. • Ph: +44 (0) 1536 406999 • Fax: +44 (0) 1536 406777 Unit 17 - Cronin Courtyard, Weldon South Industrial Estate, Corby - Northamptonshire NN18 8AG...
  • Página 2 3/8” x 11 m Reel Inlet Connection 3/8” FPT 3/8” FPT 3/8” FPT 3/8” FPT Max. Operating Pressure 35 bar 21 bar 35 bar 21 bar Max. Operating Temperature 99 °C 65 °C 99 °C 65 °C Page 2 www.reelcraft.com...
  • Página 3: Instalacion

    Remueva todos los resortes de tension antes del proceso de desmontaje. Page 3 Form# R831-696 Rev: 1/2016 Reelcraft International Inc. • Ph: +44 (0) 1536 406999 • Fax: +44 (0) 1536 406777 Unit 17 - Cronin Courtyard, Weldon South Industrial Estate, Corby - Northamptonshire NN18 8AG europe@reelcraft.com • www.reelcraft.com/europe...
  • Página 4 Coneccion de entrada del carretel 3/8” FPT 3/8” FPT 3/8” FPT 3/8” FPT Maxima presion de operacion 35 bar 21 bar 35 bar 21 bar Maxima temperatura de operacion 99 °C 65 °C 99 °C 65 °C Page 4 www.reelcraft.com...
  • Página 5: Instructions D'OPération

    Enlevez toute tension de ressort avant de désassembler. Page 5 Form# R831-696 Rev: 1/2016 Reelcraft International Inc. • Ph: +44 (0) 1536 406999 • Fax: +44 (0) 1536 406777 Unit 17 - Cronin Courtyard, Weldon South Industrial Estate, Corby - Northamptonshire NN18 8AG europe@reelcraft.com • www.reelcraft.com/europe...
  • Página 6 None 3/8” x 35’ Raccord d'entrée d'enrouleur 3/8” FPT 3/8” FPT 3/8” FPT 3/8” FPT Pression d'opération maximum 35 bar 21 bar 35 bar 21 bar Température d'opération maximum 99 °C 65 °C 99 °C 65 °C Page 6 www.reelcraft.com...

Este manual también es adecuado para:

5400 olp1185600 olp1185450 olp1185635 olp118