Stopping The Engine - Honda 600MH Instrucciones De Operación / Seguridad

2.2.4 Stopping the engine

To stop the engine:
1) Release the traction lever if the machine is in motion;
2) Lower the throttle lever to idle position;
3) Turn the switch to the OFF position.
IMPORTANT: If the on/off switch fails, close the choke to stop
the engine.
If you do not intend to start the engine soon and if you need to move
the machine, wait until the blade and all moving parts have stopped
and turn the fuel valve to the OFF position.
3. Usage
ITS COMPACT SIZE AND LOW WEIGHT ALLOW THE 600MH
PERIMETER WIRE MACHINE TO BE EASILY CARRIED IN A
SMALL VEHICLE. IT IS STRONGLY RECOMMENDED THAT YOU TURN THE FUEL VALVE
TO THE OFF POSITION (OFF).
Before each use:
● Check the soil consistency and the deepest possible insertion
depth.
● Check the engine oil level.
● Check the blade attachment.
● Check the attachment of the wire guide.
● Check the tire pressure.
3.1 Installing the perimeter wire spool
TM
The 600MH Perimeter Wire Machine is designed to
accommodate most wire spools provided by the manufacturers and
third party resellers of robot lawnmowers.
IMPORTANT: Six stepped
accommodating spools of different width and center diameters.
Select the spacers that will allow for easy insertion of the rod
and spool assembly with the most direct path to the wire guide
located behind the blade.
3.1.1 Spools mounted on a drum
The hardware provided is suitable for installation of most models up
to 800 metres (according to wire diameter):
1
2
3) Remove the shaft (with the hardware). Then remove the
hardware.
spacers are supplied
1) Unscrew the clamping handle and
remove with the flat washer.
2) Lift the shaft while opening the
blocker.
NOTE: Make sure the wire is dispensed from the top of the reel
a. Spacer(s);
b. The left centering hub (towards the inside of the spool);
c. The spool (support at the right level depending on its diameter)
on the hub;
d. The right centering hub (towards the inside of the spool);
e. Spacer(s);
f. The rubber washer;
TM
for
NOTE: When the adequate reel tension is set, you can tighten the handle's
jam bolt slightly to keep it in position. Do not overtighten to prevent damaging
the threads on the rod.
3.1.2 Spools without a drum
3.1.2.1 Spools that empty through the center
Some manufacturers supply a spool designed to be emptied through
the center. Two (2) PERIMETER WIRE BOXES 18 cm x 18 cm (part
PWMA-0002) and 22.5 cm x 22.5 cm (part PWMA- 0003), available
as optional accessories for the Perimeter Wire Machine 600MH
accepting this type of spool (up to 17.5 cm or 21 cm in diameter,
depending on the box used).
3.1.2.2 Spools with no defined shape
Some manufacturers provide wire designed to be wound around the
drum manually. As an optional accessory for the Perimeter Wire
TM
Machine 600MH , a PERIMETER WIRE DRUM (part PWMA-0001)
is available to allow the winding of the wire provided by the
manufacturer.
3.2 Moving the machine to the work zone
To move the machine to the work zone•:
1) Loosen the clamping lever on the
handle;
2) Pivot the handle until it is vertical on
the machine.
3) Lift the support foot in front the
machine.
3
4) Pull or push the machine to the work
area.
4
4) Insert in the desired order
depending on the spool used.
NOTE : The spool holding arm may need to be
adjusted to fit the spool and to avoid
unnecessary turning of the handle when setting
the reel tension.
5) Insert the shaft by sliding it into the
slots provided (arch and adjustable
spool support). Return the flat
washer and the clamping handle to
the shaft. Turn the clamping handle
until there is sufficient tension to
prevent the spool
wheeling.
EN
.
from free
TM
,
4 4