1)
TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a)
Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the "OFF" position.
b)
Unscrew the fuse(s), or switch "OFF" the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c)
Place the wall switch in the "OFF" position. If the fixture
to be replaced has a switch or pull chain, place those in
the "OFF" position.
2)
Thread hexnut onto threaded pipe so that 5 threads are
exposed below hexnut. From underside of mounting strap,
thread long end of threaded pipe into hole in mounting strap
until hexnut touches mounting strap. Tighten hexnut against
mounting strap.
3)
Thread second hexnut onto other end of threaded pipe.
Tighten hexnut up against mounting strap.
4)
Attach mounting strap to outlet box. (Screws not provided)
5)
Grounding instructions: (See Illus. A or B).
A)
On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector.
(Not provided.) After following the above steps. Never connect
ground wire to black or white power supply wires.
A
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
GREEN GROUND
SCREW
6)
Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
Connect Black or
Red Supply Wire to:
Black
*Parallel cord (round & smooth)
Clear, Brown, Gold or Black
without tracer
Insulated wire (other than green)
with copper conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
7)
Push fixture to wall, carefully passing threaded pipe through hole
in canopy.
8)
Screw threaded cap onto threaded pipe. Tighten threaded
cap to secure fixture to wall.
9)
Insert recommended bulbs.
10) Set roof down on top of fixture.
11) Thread screws down through holes in roof and into fixture.
Tighten screws to secure roof to fixture.
INSTRUCTIONS FOR MOUNTING FIXTURE OUTDOORS AND/
OR IN WET LOCATIONS.
12) Mounting surface should be clean, dry, flat and 1/4" larger
that the canopy on all sides. Any gaps between the mounting
surface and canopy exceeding 3/16" should be corrected
as required.
13) With silicone caulking compound, caulk completely around
where back of canopy meets the wall surface to prevent
water from seeping into outlet box.
Date Issued: 10/4/13
B
WIRE CONNECTOR
(NOT PROVIDED)
FIXTURE
GROUND
OUTLET BOX
GROUND
CUPPED
GREEN GROUND
SCREW
WASHER
Connect
White Supply Wire to:
White
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with silver conductor
Neutral Wire
We're here to help
FIXTURE
ARTEFACTO
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
866-558-5706
Hrs: M-F 9am to 5pm EST
ROOF
TECHO
SCREW
TORNILLO
THREADED PIPE
TUBO ROSCADO
MOUNTING STRAP
PLANCHA PARA
MONTAR
HEXNUT
TUERCA HEXAGONAL
THREADED CAP
BOLA ROSCADO
IS-49501-US