Safety In The Workplace; Cleaning And Maintenance - UNIPRODO UNI_CLOCK_03 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 11
EN
U S E R M A N U A L
TECHNICAL DATA
Parameter description
Parameter value
Product name
Wall Clock
Model
UNI_CLOCK_03
Digit size [mm]
6
Frequency [kHz]
77.5
Band [Hz]
77±300
Battery type
1.5V AA LR6
Dimensions [cm]]
Ø17x4.5
Weight [kg]
0.345
1. GENERAL DESCRIPTION
The user manual is designed to assist in the safe and
trouble-free use of the device. The product is designed
and manufactured in accordance with strict technical
guidelines, using state-of-the-art technologies and
components. Additionally, it is produced in compliance
with the most stringent quality standards.
DO NOT USE THE DEVICE UNLESS YOU HAVE
THOROUGHLY READ AND UNDERSTOOD THIS
USER MANUAL.
To increase the product life of the device and to ensure
trouble-free operation, use it in accordance with this
user manual and regularly perform maintenance tasks.
The technical data and specifications in this user manual
are up to date. The manufacturer reserves the right to
make changes associated with quality improvement.
LEGEND
The product satisfies the relevant safety
standards.
Read instructions before use.
The product must be recycled.
PLEASE NOTE! Drawings in this manual are for
illustration purposes only and in some details may
differ from the actual product.
The original operation manual is written in German.
Other language versions are translations from the
German.
2. USAGE SAFETY
ATTENTION! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in serious injury or even
death.
The terms "device" or "product" are used in the warnings
and instructions to refer to < Wall Clock>.

2.1. SAFETY IN THE WORKPLACE

a)
If there are any doubts as to the correct operation
of the device, contact the manufacturer's support
service.
b)
Only the manufacturer's service point may
repair the device. Do not attempt any repairs
independently!
6
c)
Please keep this manual available for future
reference. If this device is passed on to a third
party, the manual must be passed on with it.
d)
Keep packaging elements and small assembly
parts in a place not available to children.
e)
The device is not a toy. Children must be
supervised to ensure that they do not play with
the device.
2.2. SAFE DEVICE USE
a)
Device repair or maintenance should be carried
out by qualified persons, only using original spare
parts. This will ensure safe use.
b)
Clean the device regularly to prevent stubborn
grime from accumulating.
c)
Do not run the device when empty.
d)
It is forbidden to interfere with the structure of
the device in order to change its parameters or
construction.
e)
The device automatically synchronizes with the
master clock's radio signal and, if necessary,
adjusts the positions of seconds, minutes or
hours.
f)
The signal needed for synchronization may be
weakened by concrete or metal. The clock must
not be installed in concrete basements or inside
metal cages.
g)
In large concrete office buildings or blocks of flats,
the clock should be positioned in the vicinity of
a window for better radio signal reception. Avoid
installing the device near strong magnetic fields or
other devices generating a lot of electrical noise
(e.g. motors).
3. USE GUIDELINES
The product is used for continuous time measurement.
Current time can be arrived at in two ways: by automatic
synchronization (DCF77 system) or by manually setting
the time:
The device is radio controlled; when it receives
radio
signal
from
a
national
or
regional
transmitter, it automatically sets the time (the
internal antenna is a receiving antenna).
If the device is located in an area with no radio
signal, the time should be set manually.
The user is liable for any damage resulting from
unintended use of the device.
3.1. DEVICE DESCRIPTION
UNI_CLOCK_03
C
E
D
A
F
B
A.
Locking pin
H
G
B.
Battery compartment
C.
Reset button / Reset
point
I
D.
"M.SET" button
E.
Button used to force
reception
F.
Temperature display
G.
Eyelet
H.
Suction cups
I.
Stand
3.2. PREPARING FOR USE/ DEVICE USE
First use and auto synchronization:
a)
Unscrew the clock cover.
b)
Remove the locking pin (A) and insert the battery
in the battery compartment (B) according to the
markings on the device.
c)
The hands will move towards 12:00.
PLEASE NOTE: When the position of the seconds
hand is between 11:55 and 12:00, the hand will
make a full turn before stopping at 12:00. The
same happens with the minutes hand when it
is in between 11:52 and 12:00. The current air
temperature will be displayed on the temperature
display (F).
d)
Put the clock cover back again (remember to set it
in the right position).
e)
Select the location where you want to install the
product. The device can be attached to a vertical
surface using the eyelet (G) or suction cups (H). If
the device is placed on a horizontal surface, use the
support (I).
7
EN
f)
Wait for the device to receive synchronization
signal from the master clock. It may take up to 15
minutes. Please note that the signal received is
usually stronger at night.
g)
After synchronizing, the hands will begin to
approach the position indicating the correct time.
h)
When the clock does not receive a radio signal, it
will start showing incorrect time and the device
will attempt to synchronize.
Manual time setting:
a)
Press and hold the M.SET button (D). After approx.
3 seconds the minute and hour hands will start to
move.
b)
Press and hold the M.SET button and release it
a few minutes before the desired time setting.
c)
To go to the next minute, continue pressing and
releasing the button until the desired time is
reached.
d)
If the button is not pressed within 7 seconds,
the clock will start counting the time from the
indicated position.
Forcing time synchronization
a)
To force time synchronization, press and hold the
forced reception button (E) for about 3 seconds.
Then, the device will attempt to synchronize with
the master clock.
b)
When synchronization succeeds, the hands will
start to move towards the correct time reading. If
synchronization fails, the hands will move to the
time previously indicated.
Reset
a)
To reset the time reading, press the reset button
(C).
b)
All hands will move to 12:00 position and the
memory will be wiped out. The clock will attempt
to synchronize with the master clock.

3.3. CLEANING AND MAINTENANCE

a)
Use only non-corrosive cleaners to clean the
surface.
b)
After cleaning the device, all parts should be dried
completely before using it again.
c)
Store the unit in a dry, cool place, free from
moisture and direct exposure to sunlight.
d)
Do not spray the device with a water jet or
submerge it in water.

Publicidad

Tabla de contenido
loading

Tabla de contenido