Tabla de contenido
Publicidad
them may result in serious injury. If swallowed, consult a physician immediately.
Z47-A
17010
•
HALT USE IMMEDIATELY IF A PROBLEM APPEARS. Failure to do so may cause personal injury or damage
to the product. Return it to your authorized Alpine dealer or the nearest Alpine Service Center for repairing.
•
HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS. The wiring and installation of this unit requires
special technical skill and experience. To ensure safety, always contact the dealer where you purchased this
product to have the work done.
•
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY. Be sure to use only the specified
accessory parts. Use of other than designated parts may damage this unit internally or may not securely install
the unit in place. This may cause parts to become loose resulting in hazards or product failure.
•
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE. Route the
cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent
crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent
the wire's insulation from being cut by the metal edge of the hole.
•
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST. Avoid installing the unit in locations
with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product
failure.
SERVICE CARE
◆ IMPORTANT NOTICE
This Amplifier has been type tested and found to
comply with the limits for a Class B computing device in
accordance with the specifications in Subpart J of Part
15 of FCC Rules. This equipment generates and uses
radio frequency energy, and it must be installed and
used properly in accordance with the manufacturer's
instructions.
◆ For European Customers
Should you have any questions about warranty, please
consult your store of purchase.
◆ For Customers in other Countries
IMPORTANT NOTICE
Customers who purchase the product with which this
notice is packaged, and who make this purchase in
countries other than the United States of America and
Canada, please contact your dealer for information
regarding warranty coverage.
SPECIFICATIONS
RMS Continuous Power (at 14.4 V)
•
Per channel into 4 ohms
•
Per channel into 2 ohms
THD+N (Reference: 10 W / rated power into 4 ohms)
S/N Ratio (IHF A Weighted, Reference: rated power into 4 ohms)
S/N Ratio (IHF A Weighted, Reference: 1 W into 4 ohms)
Input Impedance
Frequency Response (Reference: 1 W into 4 ohms)
Crossover Frequency (Variable, L.P.F Only, 1/2 ch)
Input Sensitivity (V / at 10k ohms)
Dimensions
Weight
NOTE:
•
For product improvement, specifications and design are subject to change without notice.
All manuals and user guides at all-guides.com
•
Width
•
Height
•
Depth
CAUTION
SERIAL NUMBER:
INSTALLATION DATE:
INSTALLATION TECHNICIAN:
PLACE OF PURCHASE:
◆ IMPORTANT
Please record the serial number of your unit in the
space provided here and keep it as a permanent
record. The serial number plate is located on the rear
of the unit.
PDX-M12GC
1200 W x 1
1200 W x 1
0.004% / 0.04%
123 dBA
92 dBA
10k ohms
5 Hz – 400 Hz / 0 dB ~ -3 dB
50 Hz – 400 Hz (-24 dB / oct)
0.1 V - 8.0 V with Input Level
257.0 mm (10-1/8")
50.8 mm (2")
192.0 mm (7-9/16")
3.03 kg
2.82 kg
l'i
vé
•
G
L'
m
•
IN
en
un
•
FA
ap
l'i
•
U
le
do
ut
•
FA
M
ar
un
en
•
N
à
po
SO
◆
Cet
limi
B, c
15,
hau
con
◆
Pou
rev
◆
Pou
des
du
car
d'in
SP
Pu
•
P
•
P
TH
Ra
Ra
Im
Ré
Fré
Se
Dim
Publicidad
Tabla de contenido
