Operating Information; List Of Accessories; Scope Of Supply - Weller WFE P Manual De Uso

English
Warning:
When using cleaning agents, the legal safety provisions
with regard to their handling must be observed. The
cleaning agent must be treated as hazardous waste.
If the extraction performance of a cleaned FE soldering bit is
no longer adequate, the filters must be checked. The prelimi
nary filter can be changed several times before the main fil-
ter has to be replaced.
When original Weller filters are used in the prescribed man-
ner, the service lives of the particulate filter and the wide
band gas filter are designed to be approximately equal.
To change the filters, the two release buttons (3) for the lif-
ting device must be pressed simultaneously. The built-in lif-
ting device lifts up the pump casing (2) and exposes the
main filter cartridge (6). Following this, the main filter cartrid-
ge and the preliminary filter below it can be replaced without
the use of tools (see also exploded-view drawing).
Before the new main filter cartridge is fitted it should be
marked with the date of installation. The unit should be
installed in reverse sequence.
Warning:
When inserting filters, take care to follow the correct
sequence and fit them in the appropriate position. The
soiled filters must be treated as hazardous waste.

4. Operating information

The pump casing (2) simultaneously acts as a heat sink and
consequently heats up. Excessive heating is prevented by a
built-in thermal cut-out.
The WFE P soldering fume extraction unit is not suitable for
the extraction of flammable gases.

5. List of accessories

FE soldering iron for soldering fume extraction
T005 33 150 99 FE 50 soldering iron set 50 W
T005 32 152 99 FE 50M Magnastat soldering iron 50 W
T005 33 151 99 FE 75 soldering iron set 80 W
T005 26 162 99 FE 80 soldering iron 80 W
T005 29 162 99 WSP 80 FE soldering iron 80 W
10
Supplementary parts
T005 29 167 99 FE accessory for WSP 80
T005 29 177 99 FE accessory for WMP
T005 25 125 99 FE accessory for LR 21, LR 82, TCP S
T005 13 125 99 FE accessory for DS 22, DS 80, DSX 80
T005 28 126 99 FE accessory for WSF P5/8
T005 36 352 99 Locking clip for FE soldering iron
T005 25 410 00 Replacement hose for all FE soldering
irons (by the metre)
T005 29 186 99 FE accessory kit with suction pipes
ø 6 mm for WSP 80, WP 80, MLR 21,
MLR 80, WMP
T005 29 185 99 FE accessory kit with suction pipes
ø 4.5 mm for WMRP and WSP 80,
WP 80, MLR 21, MLR 80, WMP
T005 87 448 75 Clip set for FE accessory pipe ø 4.5 mm
T005 87 448 76 Clip set for FE accessory pipe ø 6 mm
T005 15 156 99 WDH 50 stand for soldering iron WMRP
with accessory kit
T005 15 076 99 Stop and go iron stand KHE
T005 15 065 99 Cable clip for AK 20
T005 15 066 99 Cable clip for KH 20/23
T005 36 412 00 Fine particulate air filter F7

6. Scope of supply

The WFE P is equipped with:
1 fine particulate air filter F7
1 main filter cartridge consisting of Class E12 particulate
filter and gas filter:
50% activated carbon, 50% Puratex
1 mains cable
1 set of operating instructions
1 Safety Information
Illustration: exploded-view drawing - see page 47
Subject to technical alterations and amendments!
See the updated
www.weller-tools.com.
operating instructions at