Product Cleaning - Martinelli MILANO Navetta XL Manual De Instrucciones

2 3• Position of the Navetta XL on a 2-person rear seat. The
Navetta XL can be positioned with the part for the feet of
the child facing in either direction.
If the seat of the vehicle inclines, towels can be used to
provide a horizontal surface.
2 4• Take the rear seat belt, fold it as shown in the figure
(arrow_a) and insert it in the slot of the car kit's metal
fastener (arrow_b).
2 5• Insert the red lever on the metal fastener of the car kit inside
the folded belt (arrow_c).
Move the metal fastener as near as possible to the seat in
order to enable it to be fastened to the Carrycot (arrow_d).
2 6• Hook the car kit connector to the ring on the Carrycot and
pull firmly on the belt to ensure the Carrycot fits as well as
possible to the seat.
• Repeat the same operations on the other side of the Carrycot.
2 7• Car Carrycot installed in the car.
2 8• UNFASTENING THE CARRYCOT FROM THE CAR:
press the control button on the connector to loosen the
belts, as shown in the figure. Unhook the fastener of the car
kit connector from the ring on the Carrycot.
IMPORTANT: the car kit can remain fastened to the
seat belts of your car. The car kit fastener can easily be
attached to or removed from the ring on the Carrycot.
Putting the child in the Navetta XL
2 9• 3-POINT SAFETY HARNESS: Slacken the straps by pressing
on the buckle (fig_a) and lengthen them (fig_b).
3 0• Press the red button (fig_a) and release the straps from the
leg divider (fig_b).
3 1• Place the child in the Navetta XL, then buckle together the
straps and the leg divider.
3 2• The child must be securely fastened in the Navetta XL. If
the straps are loose, tighten them by pulling on the end.
The straps must be as tight as possible to protect the child
in the event of an accident. Leave a minimal amount of
play (the width of a finger between the harness and the
child's chest).
3 3• REMOVE THE STRAPS: To remove the straps from the shell
of the Navetta XL, pass the buckles of the leg divider
through the slots underneath it and pull them through
All manuals and user guides at all-guides.com
• Brush the fabric parts to remove dust and hand wash at a
• Do not use chlorine bleach.
• Do not iron.
• Do not dry clean.
• Do not remove stains with solvents and do not tumble dry.
• This product requires a small amount of maintenance.
• Keep all moving parts clean and if necessary lubricate
• Clean the plastic parts periodically with a damp cloth. Do
• Brush the fabric parts to remove dust.
• Do not clean the polystyrene shock absorbing device with
• Protect the product from atmospheric agents: humidity,
• Store the product in a dry environment.
• CLEANING THE NAVICELLA BASSINET UNIT RAIN COVER: wash
3 4• COVER ALL RAIN CANOPY: made of clear.
BORSA CAMBIO: satchel with pad for changing baby's
3 5• BASSINET STAND: Practical, compact support base.
3 6• ANTI-SUFFOCATION SET: mattress plus cushion. Compatible
20
(fig_a).
To remove the strap fasteners from under the shell, release
them from the clips and pass them through the slots
(fig_b).
Padding cleaning instructions
maximum temperature of 30° without wringing.

Product cleaning

Cleaning and maintenance must only be carried out by adults.
them with light oil.
not use solvents or similar substances.
solvents or other similar products.
rain or snow. Extended exposure to sunshine can cause
colour changes in many materials.
with a sponge and soapy water; do not use detergents.
Accessories
diaper. Fastens to the chassis.
with our 3-point car kit.