Illustrated Description; Maintenance Instructions; Repair Service; Warranty Card - stayer LU260E Manual De Instrucciones

Higher speed is obtained when the dial 14 is turned in the
direction of number 6; lower speed is obtained when it is
turned in the direction of number 1.
The speed adjusting dial 14 can be turned only as far
as 6 and back to 1. Do not force it past 6 or 1, or the
speed adjusting function may no longer work.
2.2

Illustrated description

1 Ventilation grill
2 Handle adaptation orifice
3 Shaft lock
4 Loop handle
5 Bolts
6 Hex wrench
7 Wool pad
8 Side grip
9 Gum Base (base of velcro)
10 Spindle
11 Cover brushes
12 Switch trigger
13 Lock button
14 Speed adjusting dial
15 Lock nut
16 Abrasive disc
17 Carbon brushes
18 Lock nut wrench
3 Operating instructions
3.1 Placement and testing
Always wear safety glasses or a face shield during
operation.
Pull the trigger 12 and turn the speed adjusting dial 14 until you
obtain the appropriate speed for your work. When polishing,
keep the wool pad 7 at an angle of about 15° to the workpiece
surface (Fig. 8).
Using caps or disks
Installing or removing
(Fig. 1, 9 & 10)
Always be sure that the tool is switched off and
unplugged before installing or removing the abrasive
disc.
Mount the rubber pad 9 onto the spindle 10. Fit the caps 7 or
disks 16 on over the rubber pad 9 and screw the lock nut 15
onto the spindle 10. Press the shaft lock 3 and tighten the lock
nut 15 using the lock nut wrench 18. To remove the caps 7 or
disks 16, follow the installation procedure in reverse.
The rubber pad, abrasive disc, lock nut and lock nut
wrench are optional accessories.
Operation (Fig. 11)
Always wear safety glasses or a face shield during
operation.
(fig. 8)
ENGLISH
12
Hold the tool's switch 12 handle 19 and the loop handle 4
firmly with both hands during operation.
Keep the wool cap 7 or abrasive disc 16 at an angle of about
15° to the workpiece surface (Fig. 11).

4.Maintenance instructions

Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Replacement of carbon brushes (Fig. 12 & 13)
Replace carbon brushes 17 when they are worn. Both identical
carbon brushes 17 should be replaced at the same time.
To maintain product safety and reliability, repairs, maintenance
or adjustment should be carried out by a STAYER Authorized
Service Center.

4.1 Repair service

Our after-sales service responds to your questions
concerning maintenance and repair of your product as well
as spare parts. Exploded views and information on spare
parts can also be found under:
info@grupostayer.com
Our customer consultants answer your questions
concerning best buy, application and adjustment of
products and accessories.
4.2 Warranty

Warranty card

Included in the documentation that accompanies this
equipment, you should find the warranty card. You should
fill out the card completely and return to vendor with a copy
of purchasing receipt or invoice and you should receive a
receipt.
Note: If you cannot find the warranty card within the
documentation, you must ask for it through your supplier.
The warranty is limited only to manufacturing defects and
expire if pieces have been removed or manipulated or
repaired other than the manufacturer.

4.3 Disposal and recycling

The machine, accessories and packaging should be sorted
for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into household waste!
According the European Guideline 2012/19/UE
for Waste Electrical and Electronic Equipment
and its implementation into national right, power
tools that are no longer usable must be collected
s e p a r a t e l y a n d d i s p o s e d o f i n a n
environmentally correct manner.
Subject to change without notice.
12