Technical Data; Brief Description - Felisatti DI 22/1200GE2 Instrucciones De Servicio

Hammer drill
Rated power
No load speed
Work shaft thread
Drill chuck capacity
Max. steel capacity
Max. wood capacity
Max. concrete capacity
N strikes in load
Ø head setting neck
Acoustic pressure
Sound-power level
Vibration acceleration
Weight according EPTA-Procedure 01/2003
Follow very carefully the instructions in this manual, save it
and keep close at hand, ready to carry out any inspection
of parts that may be necessary.
If the machine is used carefully and normal maintenance is
carried out, it will work well for a long time.
The functions and use of the tool you have bought shall be
only those described in this manual. Any other use of the
tool is strictly forbidden.
Date of manufacture of the machine on an information
plate, as month and year.
ILLUSTRATIONS
DESCRIPTION (See figures)
A. Safety screw (Fig.2)
B.
Key-operated drill chuck (Fig.1 and Fig.2)
C.
Machine neck (Fig.2)
D.
Striking-drilling lever (Fig.1)
E. Turn direction lever (Fig.1)
F. On-/off switch (Fig.1)
G. Retainer button (Fig.1)
H. Thumbwheel for speed preselection (Fig.1)
I. Mechanical speed shift lever (Fig.1)
J.
Auxiliary grip (Fig.1)
K.
Drill chuck key (Fig.1, Fig.2)
L.
Depth stop (Fig.1)
EQUIPMENT
- Auxiliary handle
- Depth gauge
- Drill chuck key
- Operating instructions with Safety instructions
- Warranty

BRIEF DESCRIPTION

The machine is intended for impact drilling in brick, concrete
and stone as well as for drilling in wood, metal and plastic.
Machines with electronic control and right/left rotation are
also suitable for screwdriving and thread-cutting.

TECHNICAL DATA

W
/min
UNF
mm
mm
mm
mm
/min.
mm
dB(A)
dB(A)
m/s²
Kg
Use of the tool: These hammer drills can be used for
hammer drilling in stone, drilling in wood, metal as well as
plastic, and also for driving screws with driving bits installed
in a key chuck. Any other use not mentioned is not allowed.
Additional features of the hammer drill:
- The machine is equipped with a safety clutch or
mechanism which operates when a bit seizes up, protecting
the user and the machine's electro-mechanical parts. The
clutch is released automatically.
Warning! This machine must not be used with hole saws,
core bits, diamond bits, etc, as they tend to jam in the hole
easily. This would cause the safety clutch to trip out too
often.
- Change direction of rotation with switch lever E –due to a
lockout mechanism, switching the lever is only possible if
the On/off switch F is not depressed.
- Electronic control of spindle speed, infinitely variable by
finger pressure on the On/off switch F.
- For continuous operation the On-/Off switch can be
locked in the "On" position by the button G.
- Adjustable auxiliary handle J, with integral depth gauge L.
BEFORE USING THIS TOOL
WARNING! Before carrying out any work, check, for
instance, using a metal detector, that there are no electric
wires or gas or water pipes under the surfaces you wish to
work on. Make sure the mains voltage is correct: it must be
the same as that on the specification label. Machines with
230V can also be connected to a 220-V mains supply. To
turn the machine on, press the ON/OFF switch F and keep
it pressed down. When the ON/OFF switch is released, the
machine stops.
WARNING! Always disconnect the plug from the socket
before doing any work on the machine.
1. Drill chuck
These models feature key-operated drill chucks.
Changing drill chucks (Fig. 2)
Insert it in the tool and tighten with drill chuck key L
DI22/1200GE2
1200
0-830/0-2000
½"x20
3...16
22
50
35
13280-32000
43
96
107
19,5
3,6
5