Talk 2 All - Universal Intercom With Different Brand Unit; Compatibility With Midland Bt Line Units; Pairing The Midland Btx2 Pro To Bluetooth Devices - Midland BTX2 PRO Manual De Instrucciones

Talk 2 All - Universal Intercom with different brand unit.

Thanks to the "Talk2 All - Universal Intercom" feature it is now possible to pair your Mi-
dland BTX2 PRO to a different brand intercom available on the market.
You can pair a not Midland Intercom on the "Forward" button.
› On the Midland BTX2 PRO enter the setup mode: (with the unit OFF press and hold
down the Middle button about 7 sec. until the Red light is on permanently).
› Keep pressed the "Forward" button for 7 seconds: the Red and Blu LED light will start
flashing fast, then (while you still keep the button pressed) the Red and Blu LED lights
will change to slow flashing. Now you can stop pressing the button.
Talk2All - Universal Intercom
Not Midland Unit
On the other intercom (not Midland brand) follow the procedure to pair to a phone,
because the BTX2 PRO is paired as a Phone.
If successfully paired the red/blue light will stop flashing and the blu light will slowly flash
instead.
Attention: remember to switch OFF all the other Bluetooth devices during the pairing proce-
dure, only the two devices involved in the pairing must be turned on.
To open/close the "Universal Intercom" communication on the Midland BTX2 PRO
press very long (7 sec) in "Intercom" mode the Forward button. On the other intercom
just press the phone redial or voice dial button.
Maybe it will be necessary to press the redial button two times, depending on the model
of the not Midland intercom.
Attention: In order to use the the "Talk2All-Universal Intercom" feature the pairing on the
other unit must be done as a phone. The other intercom (not Midland brand) will be able to be
paired to a phone only if two phones are supported.
www.midlandeurope.com
All manuals and user guides at all-guides.com
You can pair also a Midland unit as Talk2All, that means the pairing must be done as a
phone (one unit use the Talk2All procedure and the other unit use the pairing to "Phone"
procedure).

Compatibility with Midland BT line units

The BTX2 PRO is compatible with BTX1 PRO, BTNext PRO, BT Next Conference,
BTX2 FM and BTX2 FM.
When paired the max distance of the intercom is defined from the lower possible.
The BTX2 PRO is compatible with the previous line of Midland BT (BT Next, BTX2 and
BTX2) only if updated to firmware version 2014 or later.

Pairing the Midland BTX2 PRO to Bluetooth devices

The Midland BTX2 PRO unit can be paired to other Bluetooth devices, like Pho-
ne, GPS Navigator or PMR446 Radio with built-in or external Bluetooth (dongle).
The pairing procedure must be done using the "Volume +" or the "Volume -" buttons.
› Pairing to the "Volume +" button: for Phone with music A2DP stereo, GPS Navigator
with A2DP audio or external mono/Stereo A2DP dongle.
› All devices paired to "Volume +" button have higher priority and will interrupt all the
other communications (like Intercom, FM Radio and Music).
› Pairing to the "Volume -" button: for a second phone with mono audio (Hands Free
Protocol) for GPS navigators/ Radar detector and other devices with mono audio.
MONO MONO and STEREO
› Phone (HFP Mono) › Phone (HFP/A2DP Stereo)
› GPS (HFP/A2DP Stereo)
› GPS mono
› Dongle (HFP/A2DP Stereo)
› PMR446 Transceiver
25