Matco Tools TLS788 Guia Del Usuario

WARNING
Study, understand and follow all instructions provided with this product.
Read these instructions carefully before installing, operating, servicing
or repairing this tool. Keep these instructions in a safe accessible place.
INTENDED USE OF THE TOOL
These Torque Limiting Extension Bars are designed to quickly
attach wheels while limiting torque. NOT TO PERFORM THE
FINAL INSTALLATION OF WHEELS. A TORQUE WRENCH IS
REQUIRED TO TORQUE WHEELS TO THEIR SPECIFICATION.
WARNING
• Use of this product can expose you to chemicals such as
phthalates which are known to the State of California to cause
cancer, and birth defects or other reproductive harm. For
more information go to www.P65Warnings.ca.gov/product.
Always wear ANSI approved safety equipment, safety glasses
and clothing when using this product. Study, understand, and
follow all instructions provided with this product. Failure to
read and follow all warnings and operating instructions may
result in damages and serious injury or death.
• Always wear ANSI approved goggles when using this
product. (Users and bystanders).
• Never use this tool for any application other than for
which it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool,
modification of the tool, or use of the tool with accessories
not designed for it could result in serious injury or death.
• Always select the correct accessories of the correct size and
design for the job that you are attempting to perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
• Do not begin repairs without assurance that vehicle is in
secure position, and will not move during repair.
10 PIECE
TORQUE LIMITING
EXTENSION BAR SET
MODEL:
10 PIECE TORQUE LIMITING
TLS788
EXTENSION BAR SET
The manufacturer warrants this product to the original user against defective
material or workmanship for a period of 1 year from the date of purchase.
The manufacturer reserves the right to determine whether the part or parts
failed because of defective material, workmanship or other causes. Failures
caused by accident, alteration, or misuse are not covered by this warranty.
The manufacturer, at its discretion, will repair or replace product covered
under this warranty free of charge. Repairs or replacements of products
covered under this warranty are warranted for the remainder of the original
warranty period.
The manufacturer or its authorized service representatives must perform all
warranty repairs. Any repair to the product by unauthorized service
representatives voids this warranty. The rights under this warranty are limited
to the original user and may not be transferred to subsequent owners.
The warranty is in lieu of all other warranties, expressed or implied, including
warranties of merchantability and fitness for a particular purpose. Some
states do not allow the exclusion or limitations of incidental or consequential
damages, so the above limitations may not apply to you.
When unpacking, check the parts diagram and part number
listing on page 3 to make sure all parts are included. If any
parts are missing or damaged, please call your distributor.
PRODUCT INFORMATION:
• Quickly mount wheels to the vehicle while limiting torque
• Increase efficiency and eliminate damage caused by
impact wrenches.
• No maintenance or calibration necessary.
• Color coded.
• Material: CR-MO with matt finish.
• Set Includes the following 1/2" Drive /8" Torque Limiting
Extension Bars:
65ft/lbs (90Nm)
75ft/lbs (100Nm)
80ft/lbs (110Nm)
90ft/lbs (120Nm)
100ft/lbs (135Nm)
USE A TORQUE WRENCH TO TORQUE LUG NUTS TO FINAL SPECIFICATION,
DO NOT USE THIS TOOL BY ITSELF !
MADE IN TAIWAN
Page 1
1 YEAR LIMITED WARRANTY
Unpacking
110ft/lbs (150Nm)
120ft/lbs (160Nm)
130ft/lbs (175Nm)
140ft/lbs (190Nm)
150ft/lbs (200Nm)
DO NOT DISCARD – GIVE TO USER