Rousseau SH Serie Guía De Montaje

Heavy-duty back panel
SH Line
Hardware
1/4-20 bolts
1/4-20 bolts
Pernos 1/4-20 Pernos 1/4-20
5/8"
1"
Panel position
The panels should be installed as shown on this
drawing.
Round tab against the double lap.
Lower panel to be installed center
holes upward.
Upper panel to be installed center
holes downward.
42'' wide shelving and less / Anaqueles de 42" y menos de ancho
Post height* Bottom panel
Altura de poste* Panel inferior
SR10-075 SHSC-XX39
SR10-081 SHSC-XX51
SR10-087 SHSC-XX51
SR10-093 SHSC-XX63
SR10-099 SHSC-XX51
SR10-105 SHSC-XX57
SR10-111 SHSC-XX63
SR10-117 SHSC-XX63
SR10-123 SHSC-XX63
SR10-129 SHSC-XX57
SR10-135 SHSC-XX63
SR10-141 SHSC-XX63
SR10-147 SHSC-XX63
48'' wide shelving / Étagères de 48" de large
Post height* Bottom panel
Altura de poste* Panel inferior
SR10-075 SHSC-4839
SR10-081 SHSC-4851
SR10-087 SHSC-4851
SR10-093 SHSC-4851
SR10-099 SHSC-4851
SR10-105 SHSC-4851
SR10-111 SHSC-4851
SR10-117 SHSC-4851
SR10-123 SHSC-4851
SR10-129 SHSC-4851
SR10-135 SHSC-4851
SR10-141 SHSC-4851
SR10-147 SHSC-4851
*If the posts are other dimensions than those in this chart, replace the SHSC top panel with a SHZS panel.
Si los postes tienen otras dimensiones que las indicadas en la tabla, reemplazar el panel superior SHSC con un panel SHZS.
rousseau.com
1-800-463-4271
Assembly Guide
Accesorios
1/4-20 nuts
Tuercas 1/4-20
Upper panel
Panel superior
Top panel Center panel
Panel superior Panel central
SHSC-XX39
SHSC-XX33
SHSC-XX39
SHSC-XX33
SHSC-XX51
SHSC-XX51
SHSC-XX51
SHSC-XX37
SHSC-XX63
SHSC-XX51 SHSN-XX24
SHSC-XX51 SHSN-XX24
SHSC-XX57 SHSN-XX24
SHSC-XX63 SHSN-XX24
Top panel Center panel
Panel superior Panel central
SHSC-4839
SHSC-4833
SHSC-4839
SHSC-4845
SHSC-4851
SHSC-4833 SHSN-4824
SHSC-4839 SHSN-4824
SHSC-4845 SHSN-4824
SHSC-4851 SHSN-4824
SHSC-4845 SHSN-4836
SHSC-4851 SHSN-4836
SHSC-4845 SHSN-4848
SHSC-4851 SHSN-4848
Page/Página 1/2
Panel posterior reforzado
Guía de montaje
Tools required Herramientas necesarias
Scratch awl
Punzón
Los paneles se deben instalar como lo muestra el
dibujo
Lower panel
Panel inferior
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Línea SH
7/16"
Phillips #3
Posición de los paneles
La lengüeta redondeada contra el
doble pliegue.
Los agujeros del centro del panel
inferior deben quedar hacia arriba.
Los agujeros del centro del panel
superior deben quedar hacia
abajo.
S33-JN20S
7D000811S