Publicidad
INSTALLATION INSTRUCTION
INSTALLATION INSTRUCTION
131 - LED Flush Mount
Slat - Vanities & Wall Sconces
168-LED Flush Mount
FM-13114
FM-16818
WS-80618/WS-80624/WS-80636
FIG. 1
WARNING
INSTALLATION INSTRUCTION
IMPORTANT: NEVER attempt any work without shutting o the electricity.
Slat - Vanities & Wall Sconces
-
Read all instructions before installing.
-
System is intended for installation by a quali ed electrician in accordance with the National Electrical Code and local regulations.
WS-80618/WS-80624/WS-80636
-
Go to the main fuse box, or circuit breaker. Place the main power switch in the "OFF" position and unscrew the fuse(s) or switch "OFF"
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
WARNING
-
Place the wall switch in the "OFF" position.
IMPORTANT: NEVER attempt any work without shutting o the electricity.
-
Read all instructions before installing.
CAUTION
-
System is intended for installation by a quali ed electrician in accordance with the National Electrical Code and local regulations.
-
All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
-
Go to the main fuse box, or circuit breaker. Place the main power switch in the "OFF" position and unscrew the fuse(s) or switch "OFF"
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
-
Place the wall switch in the "OFF" position.
AVERTISSEMENT
CAUTION
-
All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
IMPORTANT : Coupez l'électricité avant TOUTE manipulation.
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
-
Lisez toutes les instructions avant d'installer.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
-
Système est destiné à être installé par un électricien quali é en conformité avec le code national de l'électricité et les
Glass
règlements locaux.
AVERTISSEMENT
(RPL-GLA-13114)
-
Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l'interrupteur principal en position d'arrêt
IMPORTANT : Coupez l'électricité avant TOUTE manipulation.
(« OFF »).
Glass
-
Lisez toutes les instructions avant d'installer.
(RPL-GLA-13114)
-
Placez l'interrupteur mural en position d'arrêt (« OFF »).
-
Système est destiné à être installé par un électricien quali é en conformité avec le code national de l'électricité et les
Shade
règlements locaux.
(RPL-SHA-16818)
MISE EN GARDE
-
Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l'interrupteur principal en position d'arrêt
(« OFF »).
-
Toutes les pièces doivent être utilisées tel qu'il est indiqué dans ces instructions. Ne remplacez pas les pièces, n'en laissez pas de côté
-
Placez l'interrupteur mural en position d'arrêt (« OFF »).
Shade
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l'homologation ETL/CETL du
(RPL-SHA-13114)
luminaire. MISE EN GARDE Ors de la manipulation de l'appareil, ne pas appliquer de pression à la LED, tenir l'appareil par la seule bas
MISE EN GARDE
-
Toutes les pièces doivent être utilisées tel qu'il est indiqué dans ces instructions. Ne remplacez pas les pièces, n'en laissez pas de côté
ADVERTENCIA
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l'homologation ETL/CETL du
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
luminaire. MISE EN GARDE Ors de la manipulation de l'appareil, ne pas appliquer de pression à la LED, tenir l'appareil par la seule base.
-
Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
Diffuser
lámpara.
ADVERTENCIA
(RPL-DIF-13114)
-
Sistema está disenado para ser instalado por un electricista cali cado, de acuerdo con el código eléctrico nacional y las normas local
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
-
Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
-
Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
principal en la posición "OFF" (APAGADO).
-
Sistema está disenado para ser instalado por un electricista cali cado, de acuerdo con el código eléctrico nacional y las normas locales.
-
Coloque el interruptor de la pared en la posición "OFF" (APAGADO).
-
Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición "OFF" (APAGADO).
PRECAUCIÓN
-
Coloque el interruptor de la pared en la posición "OFF" (APAGADO).
-
Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la cali cación
PREPARATION
PRECAUCIÓN
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
1.
Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
-
Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
2.
Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la cali cación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
CONNECTING THE WIRES (Fig. 2)
HARDWARE
3.
Remove the mounting screws (C1) from xture.
4.
Drill holes in the ceiling aligned with the key holes located in the mounting plate, insert the plastic anchors (D1).
A1
HARDWARE
Connect the xture's input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A1) are secured.
5.
If your outlet box has a green or bare copper ground wire, connect the xture's
A1
B1
ground wire to it. Otherwise, connect the xture's ground wire directly to the
back plate using the green screw provided.
After wires are connected, tuck them carefully inside the junction box.
MOUNTING THE FIXTURE (Fig. 1)
6.
Secure the mounting plate to the junction box using junction box screws (B1),
Wire
fasten it to the wall using wood screw (E1). The side of the mounting back
Connector
Wire
Mounting
Connector
Qty: 3 pcs
Ring
plate marked "GND" must face out.
Qty: 3 pcs
Qty: 1 pc
7EAC112201
7.
Insert the PC di user into the xture shade.
7EAC112201
7MBC101501
8.
Secure the xture onto mounting plate with mounting screws (C1).
waclighting.com
modernforms.com
modernforms.com
Phone (800) 526.2588
Phone (800) 526.2588
Phone (800) 526.2588
Fax
(800) 526.2585
Fax
(800) 526.2585
Fax
(800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
G0
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY, 2017
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY, 2017
Junction Box
( C )
B1
C1
C1
D1
Mounting
Transformer
Ring
Transformer
Junction
( E )
Qty: 1 pc
Qty: 1 pc
Box Screw
Qty: 1 pc
Qty: 2 pcs
7MBC101501
5EN-2460-R2
5EN-2460-R2
+ 1 Extra
7MPF0825C1
8-32x1 SS
Headquarters/Eastern Distribution Center
Headquarters/Eastern Distribution Center
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
44 Harbor Park Drive
44 Harbor Park Drive
Port Washington, NY 11050
Port Washington, NY 11050
Port Washington, NY 11050
D1
Plastic Anchor
Junction Box
Plastic Anchor
A1
Wire Connector
Wire Connector
Mounting Plate
Mounting Plate
Wood Screw
E1
Wood Screw
Junction Box Screw
B1
Junction Box Screw
Mounting Screw
C1
Mounting Screw
Fixture
Shade
Fixture Shade
PC Diffuser
PC Di user
D1
E1
E1
F1
Fig. 2 Wiring
Junction
Conversion
( B )
Box Screw
Plate
Conversion
Mounting
Qty: 2 pcs
Plate
Qty: 1 pc
Screw
Qty: 1 pc
Qty: 2 pcs
+ 1 Extra
4MBA151110BA
4MBA151110BA
+ 1 Extra
7MPF0825C1
( C )
7MPF0415C2
8-32x1 SS
8-32x9/16 SS
Central Distribution Center
Central Distribution Center
Central Distribution Center
1600 Distribution Ct
1600 Distribution Ct
1600 Distribution Ct
Lithia Springs, GA 30122
Lithia Springs, GA 30122
Lithia Springs, GA 30122
Back Plate Dimensions
Ø2
Ø3
( D )
F1
G1
( A )
G1
H1
Fixture Wires
House Wires
Black or
Black
Smooth
(Hot)
Fixture Wires
House Wires
White or
White
Mounting
Set
Ribbed
(Neutral)
Screw
Screw
Set
Mounting
Qty: 2 pcs
Screw
Qty: 2 Extra
Anchor
Fixture Wires
House Wires
Qty: 2 Extra
Qty: 2 pcs
+ 1 Extra
7MPF0308S1
Bare wire
Green or Bare Copper
7MPF0308S1
7TDD082401
7MPF0415C2
5/32-32x5/16
5/32-32x5/16
(Ground)
(Ground)
8-32x9/16 SS
Nickel Plating
Nickel Plating
Western Distribution Center
Western Distribution Center
Western Distribution Center
1750 Archibald Avenue
1750 Archibald Avenue
1750 Archibald Avenue
Ontario, CA 91760
Ontario, CA 91760
Ontario, CA 91760
Ø7"
"
3/4
"
1/2
Ø8
"
3/4
H1
I1
I1
Mounting
Tapping
Anchor
Screw
Tapping
Qty: 2 pcs
Screw
Qty: 2 pcs
Qty: 2 pcs
7TDD082401
7MPF2204J2
7MPF2204J2
Ø4x22
Ø4x22
2
1
Publicidad
