Technical Data; Safety Instructions - Felisatti RF67/2200VE Instrucciones De Servicio

TECHNICAL DATA

Milling machine
Absorbed power
 of milling cutter attachment
No load speed
Machine weight (without accessories)
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at
hand to use when carrying out maintenance on the
indicated parts.
If the machine is used carefully and normal maintenance
is carried out, it will work for a long time.
The functions and use of the tool you have bought shall
be only those described in this manual. Any other use
of the tool is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See figures)
A Safety push button switch (Fig.2)
A1 On-/off switch (Fig.2)
B Blocking button of the clip-holder shaft (Fig.1)
C Depth adjustment handle (Fig.1)
D Clip fixing nut (Fig.1 and Fig.2)
E Depth stop (Fig.1)
F Stepped stop (Fig.1)
G Locking wing nut (Fig.1)
H Fixing lever (Fig.2)
I Side stop (Fig.3)
J Transparent frontal protection (Fig.5)
K Dust suction adapter (Fig.6)
L Speed adjustment (Fig.1)
M Fine depth stop adjustment (Fig.1)
N Depth adjustment handle (Fig.1)
O Grips (Fig.1)
P Base plate (Fig.6)
Q Sliding plate (Fig.2 and Fig.3)
R Wing screw for dust suction adapter (Fig.6)
S Strip stop (Fig.3)
T Parallel stop fine adjustment (Fig.3)
U Copier bushing (Fig.3)
V Wing screw (Fig.5 and Fig.6)
W Depth adjustment handle (Fig.2)
Y Depth adjustment scale (Fig.5)
EQUIPMENT
- Clip, 1/2" and 1/4"
- Side stop
- Fixed spanner, 22 mm and 7 mm
- Transparent guard
- Dust suction adapter
- Copier bushing
- Operating instructions

- Safety instructions

- Warranty
SAFETY INSTRUCTIONS
 See "Safety instructions" enclosed manual, supplied
together with this instruction manual.
All manuals and user guides at all-guides.com
W
rpm
mm
kg
 WARNING! The dust produced when milling asbestos
and/or silica stone materials is dangerous to health.
Follow the insurance company's safety instructions
 For your personal safety, always connect the machine
regarding the responsibility of employees.
to a mains supply by a differential and thermal cut-out
switch, in accordance with regulations on low-voltage
 Do not perforate the machine casing, as this would
wiring sitemaps.
 Always unplug the machine before doing any work on it.
destroy the protective insulation (use adhesive labels).
 Always stop the machine by switching it off, not by
 WARNING! Before each use, inspect the plug and
unplugging it.
lead. Should they need replacing, have this done by an
official service centre. Only plug the machine in when it
 Always keep the lead out of the machine's working
is switched off.
 Only plug the machine in when it is switched off.
area.
 Do not allow the machine to get wet, nor should it be
 When using the machine, always wear safety goggles,
used in wet environments.
gloves and non-slip footwear, and it is advisable to
 Check for correct piece fixing before commencing any
wear ear protection.
 Only milling heads with acceptable revolutions that are
operation.
at least the same as the maximum off-load revolutions
 The milling head shaft diameter should match the
of the machine should be used.
 It should be ensured that the milling head is firmly held
inside diameter of the tool-holder (locking clip).
 The clip-carrier shaft support lever must only be oper-
in place before the machine is operated.
 The milling head should only be brought into contact
ated when the machine is stopped.
 The machine must be firmly held by the grips. Other-
with the work-piece after it has been switched on.
wise the recoil produced could cause the machine to
 Hold the machine firmly in both hands and in a stable
work imprecisely or even dangerously.
 During use, it should be ensured that the milling head
position.
is in the centre of the copy bushing in order to prevent
 The milling machine must never be used on metal
any personal injury or damages to the work-piece.
 Hand must be kept clear of the milling machine while it
objects, such as nails and screws.
 The cutting depth must never be adjusted with the
is operating.
motor running. A mistake in this time could lead to
personal injury and/or damage to the milling head or
work-piece.
RF67/2200VE
2200
12000-21000
12
5.9