Hoover HBFUP130NKE Manual Del Usuario página 11

Use a screwdriver to adjust the gap on the lower section of the
4.
adjusting bolts. The gap should be set to approximately 9 mm (as
shown in the above drawing).
Fix the lower bracket to the bottom of the furniture door and the
5.
underneath of the appliance door (as shown in the drawing on the
previous page).
It is possible to make minor adjustments to the position of the
o
furniture door using the screws on the top and the bottom of the
appliance door. You should make these adjustments so that the
furniture door is level.
Insert the cover plate to the top of the appliance, this will just clip
6.
into place.
Open the appliance door.
7.
Use a suitably sized drill bit to drill through the holes in the bracket,
o
into the work top.
IMPORTANT: The drill bit should be appropriate for the material that
your work top is made from.
Secure the bracket to the underside of the worktop, using the
o
screws provided.
IMPORTANT: These screws should be fully tightened.
If the appliance is being installed under a granite worktop, use the L shaped
o
brackets provided to secure the fridge to the side of the cabinet. Use a
suitably sized drill bit to drill through the three holes in the bracket into the
cabinet side on the opposite side to the hinges.
The oval holes rest over the hinge positions which are not being used on the
o
front of the appliance. Use two screws to secure the bracket to the front of
the appliance.
Check that the door opens and shuts without snagging, as well as checking
o
that the door is sealing correctly.
TROUBLESHOOTING
IMPORTANT: If your freezer appears not to be operating properly, before
contacting the Customer Care Department, please refer to the checklist
below.
My freezer does not appear to be working/there is no power to my appliance.
Check that the plug is fully inserted into the power socket.
o
Check that there is power to your mains supply (e.g. that there hasn't been a
o
power cut or that the fuse hasn't blown).
Check that the thermostat inside the appliance has not been turned to the
o
<0> position.
Check that your mains supply voltage, corresponds to the voltage stated on
o
the rating plate of your appliance.
My freezer appears to be performing poorly
Check that the appliance isn't overloaded and that food hasn't been packed
o
too tightly into it.
The thermostat setting is too low; you should turn the thermostat up higher.
o
Ensure that the door is closing properly and that the door has not been
o
opened for a prolonged period in error.
Ensure that there is adequate ventilation for your appliance.
o
My freezer is noisy
The refrigerant gas that circulates the pipework of the appliance may make a
o
slight noise, even if the compressor is not running.
If the noise worsens or the appliance gets louder than normal; check that it is
o
levelled off correctly, that nothing is touching the rear of the fridge and that
nothing placed inside the appliance is rattling.
Ice has quickly formed on the inner back wall of my freezer
Check that food has not been pushed too far back inside the appliance, so
o
that it is in contact with the inner back wall.
DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF.
Please note that if an engineer is asked to attend whilst the product is under
guarantee and finds that the problem is not the result of an appliance fault,
then you may be liable for the cost of the call out charge.
The appliance must be accessible for the engineer to perform any necessary
repair. If your appliance is installed in such a way that an engineer is
concerned that damage will be caused to the appliance or your kitchen, then
they will not complete a repair.
This includes situations where appliances have been tiled in, sealed in with
sealant, have wooden obstructions placed in front of the appliance, like
plinths. Or any installation other than the one specified by Baumatic Ltd. has
been completed.
Please refer to the conditions of guarantee that appear on the warranty card
that you receive with the appliance.
11