Device Description; Connecting The Device; Cleaning And Maintenance - UNIPRODO CON.PAS8-01 Manual De Instrucciones

EN
v) Do not use the device set at high volume for a long
time.
w) Do not put the device turned on directly to your ear. It
may damage your hearing aid.
x) Use the device parameter adjustment mode only
when the device is connected to the power supply.
y) To avoid radio interference, it is recommended that
the Bluetooth device is used far from Wi-Fi routers,
laptops, microwave ovens and other signal sending
devices. The range also depends on the layout of the
rooms. For optimal performance, it is recommended
to place the device in a place where the walls or
furniture will not interfere.
3. USE GUIDELINES
The user is liable for any damage resulting from
unintended use of the device.

3.1. DEVICE DESCRIPTION

The loudspeaker allows you to play music in different
places. The device connects to the microphone and the
guitar. It can connect to external devices via Bluetooth,
AUX, USB, and microSD. It has a radio function. The
device is mobile thanks to castors mounted in its
bottom part. It has a telescopic handle. The loudspeaker
can also be fitted onto a stand; there is using a special
hole in the bottom of the device.
Please remember that the stand should have
adequate load capacity and be stable on a flat
surface!
3
2
1
1. Control panel
2. LED decoration
3. Telescopic handle
CONTROL PANEL FUNCTIONS
ATTENTION! This product's view can be found on the
last pages of the operating instructions (pp. 31).
1. DIGITAL MP3 PLAYER - LINE IN/USB/Bluetooth/FM
mode display
2. MODE BUTTON - Pressing once changes the current
operating mode between USB/SD card/FM radio/
Bluetooth.
3. Select the previous song/channel in the USB/TF/BTIn
FM mode using this button.
4. Stop/play button. Pressing for 2-3 seconds initiates
a search in the FM mode. Once the channel is found,
it is automatically saved.
5. Next song/channel selection in the USB/TF/BTIn FM
mode.
8
6. REC/PLAY - Record/play button. Insert a USB or micro
SD card with enough disc space. Press the button
twice to record the microphone sound. Press the
button again to stop recording. Press the button once
again to play the recorded sound.
7. MIC.PRI - Microphone priority button. When you
switch the microphone on and press that button, the
music volume will automatically drop.
8. Guitar volume control.
9. GTINPUT - 6.3 mm ¼ " guitar input.
10. Power ON/OFF - Power on/off switch
11. USB/micro SD - USB /micro SD card port (supports
micro SD up to 32 GB)
12. Volume - Volume control.
13. AUX - 1/8 „(3.5 mm) stereo input can be used to
connect a smartphone, MP3 player or other audio
sources.
14. BASS – bass level control.
15. TREBLE - treble level control.
16. ECHO - echo effect intensity control.
17. M.VOL - Microphone volume control.
18. Battery charge level indicator (red LED light indicates
low battery; green LED light - battery fully charged)
19. DC 9V - 9V DC power input.
20. Microphone jack - 6.3 mm ¼ " jack - the microphone,
the guitar or another musical instrument input
21. LED ON/OFF - LED lighting on/off
THE REMOTE CONTROL FUNCTIONS
1. POWER - Power on/off button
2. Buttons 0-9 - USB/micro card SD track number
selection
3. EQ button - USB/TF micro card SD equalization mode
selection - pop, rock, jazz, classic, normal
4. REP (repeat) - Repeats a song or group of songs in
a cycle.
• Pressing the button once repeats a track
• Pressing the button twice plays all the tracks in a loop
• Pressing the button three times brings back the
default playback mode
5. Selects the previous song/channel in USB/TF/BTIn FM
mode.
6. Play/Stop button.
7. VOL - Volume down button
8. MODE - Selects the operating mode. Pressing the
button once changes the current operating mode
between USB/TF SD card/FM radio/Bluetooth.
9. MUTE – Mutes the sound.
10. STOP - Stops playback.
11. Selects the next song/channel in the USB/TF/BT/FM
mode.
12. VOL + - Volume up.
THE MICROPHONE
1
2
3
4
1. Microphone cover
2. Battery charge indicator (red LED light indicates low
battery)
3. Power on/off and mute switch
4. Battery and transmitter cover
3.2. PREPARING FOR USE
APPLIANCE LOCATION
The temperature of environment must not be higher
than 32°C and the relative humidity should be less than
85%. Ensure good ventilation in the room in which the
device is being used. There should be at least 10 cm
distance between each side of the device and the wall or
other objects. The device should always be used when
positioned on an even, stable, clean, fireproof and dry
surface, and be out of the reach of children and persons
with limited mental and sensory functions. Position the
device such that you always have access to the power
plug. The power cord connected to the appliance must
be properly grounded and correspond to the technical
details on the product label.
3.3. DEVICE USE
3.3.1 BATTERY
PLEASE NOTE: The battery must be fully charged (at least
5 hours) before the first use. The battery achieves its full
capacity only after being fully charged three times.
• This device has a battery charging automatically
whenever the device is connected to a power
source. When charged, the device switches to
maintenance charging. Nonetheless, please do
not leave the device permanently plugged into the
socket!
• To achieve lasting battery performance, charge
the battery before and after each use.
• When you turn the device off with the remote
control, it is in a standby mode and uses more
energy than turned off completely by pressing
a button on the control panel.
• When the device is left for 6 months at a low
battery level, the battery may lose its capacity
permanently. The device may heat up during
charging. Do not leave the charging device
unattended.
PLEASE NOTE: If the card will not slide in, do not force it,
just turn it over and try again.

3.3.2 CONNECTING THE DEVICE

Before turning the device on, it is recommended to
place it in the middle of the room for the optimal
performance of the speaker and the wireless signal.
Please make sure that the volume level is down to the
minimum (dial no. 12).
Press the button (10) to turn the power on.
Optional:
• Connect the music player via the AUX cable (13) to
the device,
• Insert the USB or mini SD card into the port (11).
PLEASE NOTE: If the card will not slide in, do not
force it, just turn it over and try again.
• Connection in the Bluetooth mode is activated by
pressing the MODE button (2) (Description below)
• FM radio is switched on by pressing the MODE
button (2) (Description below)
Then, select the desired operating mode by pressing the
(2) button.
9 EN
Adjust the volume level on the player and/or on the
device control panel (12). For the description of control
panel functions see above. Using the description, adjust
the effect and volume level as desired. To turn on the
LED lighting, press the button (21). If the speaker is not
in use, switch it off by pressing the button (10).
FM radio
After turning the device, on with button (2) set the FM
mode. When you press the button (4) for 2 to 3 seconds,
the channels are selected automatically. Pressing the
button (4) again, channel selection will stop. To select
the previous channel press the button (3). Select the
next channel by pressing the button (5). The device can
also be remotely controlled. Use the buttons on the
remote control to select the previous channel (5) or to
select the next channel (11).
Bluetooth connection - pairing the devices
• Press the MODE button (2) to select the Bluetooth
options. The speaker is ready to pair with the
source device.
• Turn on the Bluetooth module on the source
device, and search for „karaoke 1001" on the list
• The successful pairing will be confirmed by
a beep.
• You can start sending audio in a wireless mode via
Bluetooth.
• The disconnection of the device will be confirmed
by a sound message.
The microphone
• Before you switch on the microphone, set the
volume level to the minimum, using the dial
(17). When you turn the microphone ON using
the switch (3), slowly increase the microphone
volume using the control panel dial (17).
• If you hear interfering noise after switching on
the microphone, check if the microphone cable is
correctly inserted into the socket and whether or
not the adjustment dial (16) is set to maximum.
• If you are not using the microphone, turn it OFF
using the switch (3).

3.4. CLEANING AND MAINTENANCE

a) Always unplug the device before cleaning it.
b) Use only non-corrosive cleaners to clean the surface.
c) Store the unit in a dry, cool place, free from moisture
and direct exposure to sunlight.
d) Use a soft cloth for cleaning.
e) Do not leave the battery in the device if it will not be
used for a longer period of time.
f) Do not use sharp and/or metal objects for cleaning
(e.g. a wire brush or a metal spatula) because they
may damage the surface material of the appliance.
SAFE REMOVAL OF BATTERIES AND RECHARGEABLE
BATTERIES
Remove used batteries from the device using the
same procedure by which you installed them. Recycle
batteries with the appropriate organisation or company.