Philips SBCSK310/00 Instrucciones De Manejo página 5

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 8
INSTALLATION
Your appliances must be connected to the
Power switches before you can control them
with the remote control (fig. 2) .
• Select the appliances (e.g. a lamp) you want
to control and plug them into the Power
switches (fig. 2) .
OPERATION
The connected appliances can now be
operated via the remote control (fig. 3) . The
Power switches are operated with buttons 1, 2
and 3 by default.
• If the right side (+) of a button is pressed,
the selected appliance switches on. If the
left side (-) of the button is pressed, the
selected appliance switches off again.
The Power switches can also be operated with
the last button of the remote control. This
button is designed to operate more Power
switches at the same time.
• Set the GROUP toggle switch on the rear of
the Power switches to the right side (= ON).
– The switches will now respond when the
5th button of the remote control is pressed.
If the right side (+) of the button is pressed,
all appliances switch on. If the left side (-) of
the button is pressed, all appliances switch
off again.
MANUAL OPERATION
The Power switches have a button for manual
operation. This means that your appliance can
still be operated without the remote control.
• Press button in front of the Power switch
once.
– The Power switch switches on.
• Press button in front of the Power switch
once again.
– The Power switch switches off again.
CHANGING THE HOUSE CODE
The house code is meant to prevent
interference with the Power Control System of
your neighbour.
Power Control Systems will only respond to
signals with the correct house code. To
change the house code (fig. 4) :
• Unscrew the battery door at the rear of the
remote control.
SBCSK310page 5
3. INSTALLATION
• Please check the power consumption of the
selected appliances. The Power switches
can control appliances with a maximum
power rating of 1000 Watts!
• If the selected appliances have their own
ON/OFF switches, make sure they are
switched on.
4. OPERATION
• Set the house code of the remote control by
turning the house code selection wheel
(A-P) with a screwdriver.
• Set the house code of the Power switches
by turning the house code selection wheel
at the rear of the switches (A-P) with a
screwdriver.
• Please note that the selected house-code
for the remote control and all Power
switches should be the same! The house
code's default setting is A.
CHANGING UNIT CODE
A unit code should be set on the Power
switches. The selected unit code corresponds
to the button which has to be pressed on the
remote control. If for example, unit-code 3 is
set, the Power switch is operated via the 3rd
button on the remote control. The unit code's
default setting is 1, 2 and 3. To change the unit
code (fig. 4) :
• Set the unit code of the Power switch by
turning the unit code selection wheel at the
rear of the plug (1-16) with a screwdriver.
• The Power switch is operated by pressing
the correct button on the remote control.
• It is possible to activate more Power
switches at the same time by selecting the
same unit code.
Note:
Although the unit code on the Power switch
can be set from 1 to 16, the remote control
can only operate Power switches with unit
code set from 1 to 8.
• To operate Power switches with unit code
1-4, the toggle switch on the remote control
should be set to the left (1-4).
– The first 4 buttons on the remote control
correspond with unit code 1 to 4
respectively.
– If the toggle switch on the remote control is
set to the right (5-8), the first 4 buttons
correspond with unit code 5 to 8 respectively.
5

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Sbcsk310/10Sbcsk310/05

Tabla de contenido