Technical Data; Before Operation - Scheppach bgs 700 Traducción De Las Instrucciones Originales

6. Technical data

Dimensions L x W x H mm
ø Grinding wheel mm
Grinding wheel thickness mm
ø Grinding wheel hole mm
Max. circumferential speed m/s
Belt speed m/min
Grinding /sanding belt L x W
mm
Weight kg
Drive
Rated voltage V/Hz
Power rating
Idle speed n min
-1
0
Load factor:
A load factor of S2 30 min (intermittent periodic duty)
means that you may operate the motor continuously
at its nominal power level (230 W) for no longer than
30 minutes ON period. If you fail to observe this time
limit the motor will overheat. During the OFF period
the motor will cool again to its starting temperature.
Noise:
Sound values were measured in accordance with
EN 61029.
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
WA
Uncertainty K
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Limit the noise to a minimum!
• Only use appliances which are in perfect working
order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.

7. Before operation

Before you connect the equipment to the mains sup-
ply make sure that the data on the rating plate are
identical to the mains data.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
360 x 280 x 335
150
20
12.7
23
895
686 x 50
10.2
230/50
370W S2 30min
2850
82.3 dB(A)
3 dB
91.5 dB(A)
3 dB
Always pull the power plug before making adjust-
ments to the equipment.
• The machine must be set up so that it stands firmly,
i.e. it must be securely screwed to a work bench or
similar.
• The grinder should be fixed permanently at a suit-
able place. To attach the grinder to a hard and
flat surface, there are two mounting points on the
grinder. The tool support should be approximately
at the height of your elbow. The working area is in
front of the machine - keep it free of obstacles.
• All covers and safety devices have to be properly
fitted before the equipment is switched on.
• It must be possible for the grinding wheel to run
freely.
Assembling the spark deflector (Fig. 1-3)
• Slide the spark deflector (2) under the guard hood
(5). Screw the spark deflector (2) to the guard hood
(5) by using the spark deflector adjustment screw
(3).
• Use the spark deflector adjustment screw (3) with
the spring washer and the washer to fix the spark
deflector (2). To secure you will need a screwdriver
(Fig. 2).
• Adjust the spark deflector (2) using the spark de-
flector adjusting screw (3) so that the distance be-
tween the dry grinding wheel (6) and the spark de-
flector (2) is as small as possible and certainly does
not exceed 2 mm. (Fig.3)
• Adjust the spark deflector (2) periodically to com-
pensate for wear on the wheel.
Fitting the workpiece supports (Fig. 1/4/5/6)
• Secure the workpiece supports (8) to the grinder/
sander using the workpiece support star screw (7)
on belt side and the 2 fastening screws for work-
piece support (18) on grinding wheel (5) side.
Adjusting the workpiece supports (Fig. 5+6)
• Adjust the workpiece supports (8) using the fas-
tening screws for workpiece support (18) and the
workpiece support star screw (7)so that the dis-
tance between the dry grinding wheel (6) or the
grinding/sanding belt (9) and the workpiece sup-
ports (8) is as small as possible and certainly does
not exceed 2 mm.
• Adjust the workpiece supports (8) periodically to
compensate for wear on the dry grinding wheel.
Changing the grinding wheel (Figs. 1/7-9)
Loosen the 3 fastening screws (12) for side cover (12)
holding the grinding wheel side cover (13), turn an-
ti-clockwise and take it off (Fig. 7). Slacken the nut
(Fig. 8/A) (important: the grinding/ sanding wheel is
fastened with a lefthanded thread) by holding the nut
(Fig. 9/A) of the grinding/sanding belt roller on the op-
posite side.
GB | 21