Tabla De Contenido; Technical Specifications - CMT ORANGE TOOLS CMT3 Instrucciones Para El Uso

INDEX
INTRODUCTION
1. GENERAL INFORMATION
2. TECHNICAL SPECIFICATIONS
3. GENERAL SAFETY STANDARDS
4. INSTALLATION
5. REGULATION
6. OPERATION AND USE
7. MAINTENANCE
8. PART REPLACEMENT
TABLE OF ACCESSORIES
AVAILABLE ON REQUEST
INTRODUCTION
All CMT portable tools conform with standard EN
50144, CE 98/37 machine directives and following
modifications, with EEC 73/23, EEC 93/68 and, with regard
to electromagnetic compatibility, the tools conform with
directive EEC 89/336, and with standards EN 55014-1,
EN 55014-2, EN 61000-3-2, EN 61000-3-3.
The mark on the tool guarantees its
conformity. conformity. conformity.
If used with the care and serviced regularly, this tool will
provide long-lasting and reliable service.
Carefully follow the instructions contained in this manual,
using them for reference for any eventual controls that may
need to be carried out.
1 GENERAL INFORMATION
1.0 THE AIM OF THIS MANUAL
This manual has been compiled by the manufacturer and
is an integrative part of the tool equipment.
The information contained is for the benefit of professional
operators.
This manual defines the aims for which the tool has been
constructed and contains all the necessary information to
guarantee correct and safe use.
It is therefore strongly recommended that this manual
is consulted before performing any kind of adjustment
operation, use or maintenance tasks.
Constant observance of the standard regulations
contained in this manual will guarantee both machine and
operator safety, economic working and longer functional
operation of the tool itself.
Photographs and drawings have been supplied by the
constructor for exemplifying purposes.
With the aim of following a policy of constant development
and product modernization, the constructor is entitled to
make modifications without forewarning.
1.1 TOOL IDENTIFICATION
The plate located on the left hand side of the tool identifies
the model, the data plate located on the right hand side
of the tool contains the model references, the technical
specifications of the motor and the constructor.
All manuals and user guides at all-guides.com
INSTRUCTION MANUAL FOR
PORTABLE ELECTRIC PLANER
1.1.1 IDENTIFICATION (fig.1)
page 5 A Logotype plate
» 5 B Data plate
» 5 C Handgrip
» 6 D Switch
» 6 E Depth regulation knob
» 6 F Parallel guide
» 6 G Clamping knob
» 7 H Switch unlocking push-button
» 7 I
» 49
2.1
MODEL
Voltage (V~) (*)
Current (A)
Frequency (Hz)
Absorbed power (W)
R.p.m. (unloaded) (min
R.p.m. fully-loaded (min
Plane dimensions (mm)
Cutting depth (mm)
Width of plane (mm)
Depth of rabbet (mm)
Weight (Kg)
Sound pressure emitted
Sound power emited
Vibration level (m/s
Insulation class
*
**
2.2
Parallel adjustable inclined guide, graduated support,
service spanner.
The series fittings may vary according to the model
purchased and the actual commercial situation.
2.3
Blades, Suction union, Suction unit, kit for suction unit,
stationary support.
2.4
The tool has been designed and constructed to permit
operation in all situations and in absolute safety.
In particular working conditions remember to use
protective gloves and safety goggles.
5
Guard
2

TECHNICAL SPECIFICATIONS

TECHNICAL DATA
)
-1
)
-1
Lpa (dB ) (**)
A
Lwa (dB ) (**)
A
) (**)
2
See paragraph 4.3
Surveys carried out according to standards:
EN 50144.1 - EN 50144.2.14
STANDARD EQUIPMENT:
ACCESSORIES AVAILABLE ON REQUEST:
SAFETY STANDARDS
CMT3
230-240 110
3,7 7,9
50-60
850
13000
9500
80x286
0-3
82
23
2,8
90
103
3,2
/ II