Functional Description - Makita CJ102D Manual De Instrucciones

• Be careful not to drop or strike battery.
• Do not use a damaged battery.
• Follow your local regulations relating to disposal of
battery.
Tips for maintaining maximum battery life
• Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
• Charge the battery cartridge with room temperature at
10°C - 40°C (50°F - 104°F).
• Let a hot battery cartridge cool down before charging it.
• Charge the battery cartridge once in every six months if
you do not use it for a long period of time.
• For an optimum life-time, the battery cartridge have to
be fully charged, after use.
SAVE THESE INSTRUCTIONS.
DESIGNATION OF PARTS (Fig. 1)
1. Power button
2. Battery holder pocket (Backside)
3. Power cable (Inside the battery holder pocket)
4. Hole for strap
5. Battery holder
(See the last part of this instruction manual for all the
illustrations.)
SPECIFICATIONS
Model
Temperature
adjustment steps
Outer shell:
Material
Inner shell:
USB power supply port
Operating time (h)
Medium
(With battery BL1041B)
Rated voltage (V)
Battery cartridge
• Due to our continuing program of research and
development, the specifications herein are subject to
change without notice.
• Specifications and battery cartridge may differ from
country to country.
• Operating time may differ depending on battery type
and usage condition.

FUNCTIONAL DESCRIPTION

Switch action
To turn on the jacket, push and hold the power button
(about 1.5 seconds). To turn off, push and hold the power
button again.
4
All manuals and user guides at all-guides.com
CJ102D/CJ103D
3
- Polyester (94%)
- Spandex (6%)
- Polyester (100%)
DC 5V, 2.1A
Low APPROX. 14
APPROX. 7.5
High APPROX. 4.0
DC 10.8 V - 12 V max
BL1016, BL1021B, BL1041B
Temperature adjustment
There are three temperature settings (high, medium, low).
Three LED lights means that the temperature is set to
"high", two LED lights "medium", and one LED light "low".
When you switch on the jacket, the temperature is set to
"high". Each press of the power button cycles through the
jacket's temperature setting.
Indicating the remaining battery capacity
(Fig. 2)
(Only for battery cartridges with "B" at the end of the
model number.)
Press the check button (7) on the battery cartridge to
indicate the remaining battery capacity. The indicator
lamps (6) light up for few seconds.
Indicator lamps
Lighted Off
NOTE:
• Depending on the conditions of use and the ambient
temperature, the indication may differ slightly from the
actual capacity.
ASSEMBLY
CAUTION:
• Hold the battery holder and the battery cartridge
firmly when installing or removing battery
cartridge. Failure to hold the battery holder and the
battery cartridge firmly may cause them to slip off your
hands and result in damage to the battery holder and
battery cartridge and a personal injury.
Installing or removing battery cartridge to
the battery holder (Fig. 3)
To install the battery cartridge (10), align the tongue on
the battery cartridge with the groove in the battery holder
and slip it into place. Insert it all the way until it locks in
place with a little click. If you can see the red indicator (9)
on the upper side of the button, it is not locked completely.
Always install the battery cartridge fully until the red
indicator cannot be seen. If not, it may accidentally fall out
of the battery holder, causing injury to you or someone
around you.
Do not install the battery cartridge forcibly. If the cartridge
does not slide in easily, it is not being inserted correctly.
To remove the battery cartridge, slide it from the battery
holder while sliding the button (8) on the front of the
cartridge.
Remaining
capacity
Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%