Porter Cable PC18JR Manual De Instrucciones página 4

TO PROGRAM THE MEMORY BUTTONS
Ten FM and ten AM radio stations may be independently set. After programming the
buttons, pressing the "MEM" button (F) will instantly change the frequency to the preset
station on either AM or FM wherever you have it set at the time. To program the
remaining ten channels, press the "MODE" button (I) to change AM or FM.
1. Turn power on.
2. Set the radio to desired station (see Tune or Seek Function).
3. Press and hold the memory button (F). The "Mem" icon begins flashing in the LCD
display (E). Use either of the tune buttons to select the desired memory storage location
(0-9). After the storage location is selected, the memory will be set after 5 uninterrupted
flashes of the "Mem" icon.
4. Repeat steps 2 and 3 to set the other memory buttons.
BASS BUTTON
To add bass, press the "BASS" button (H).
1. BASS displays on the LCD screen.
2. To turn the bass off, press the button again.
IMPORTANT RADIO NOTES
1. Reception will vary depending on location and
strength of radio signal.
2. Certain generators may cause background noise.
3. AM reception will most likely be clearer when
powered by a battery pack.
4. To use the auxiliary port (D), plug the output jack
®
from a CD or iPod */MP3 player into the auxillary
port as shown in figure 5. The sound from the
external source plays through the speakers of the
PC18JR.
®
*iPod is a registered trademark of Apple Inc.
DUAL 120V AC OUTLETS
Two 120V AC outlets are located on the front of the radio. With the radio plugged into a
working 120 volt source, two additional tools or other 120V products can be plugged into
the outlets.
MAINTENANCE
SERVICE NOTES
This product is not user serviceable. There are no user serviceable parts inside the radio.
Servicing at an authorized service center is required to avoid damage to static sensitive
internal components.
CLEANING
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic
parts of the radio. These chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
CAUTION: NEVER spray or in any other way apply lubricants or cleaning solvents
inside the tool. This can seriously affect the life and performance of the tool.
RADIO CLEANING INSTRUCTIONS
WARNING: Disconnect the radio from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the radio using a cloth or soft non-metallic brush. Do
not use water or any cleaning solutions.
REPLACEMENT PARTS
Use only identical replacement parts. For a parts list or to order parts, visit our service
website at www.portercable.com. You can also order parts from your nearest
PORTER-CABLE Factory Service Center or PORTER-CABLE Authorized Warranty
Service Center. Or, you can call our Customer Care Center at (888) 848-5175.
5
L
6
SERVICE AND REPAIRS
All quality tools will eventually require servicing and/or replacement of parts. For
information about PORTER-CABLE, its factory service centers or authorized warranty
service centers, visit our website at www.portercable.com or call our Customer Care
Center at (888) 848-5175. All repairs made by our service centers are fully guaranteed
against defective material and workmanship. We cannot guarantee repairs made or
attempted by others.
You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North,
Jackson, Tennessee 38305, (888) 848-5175 - Attention: Product Service. Be sure to
include all of the information shown on the nameplate of your tool (model number, type,
serial number, etc.).
ACCESSORIES
WARNING: Since accessories, other than those offered by PORTER-CABLE, have not
been tested with this product, use of such accessories with this tool could be hazardous.
To reduce the risk of injury, only PORTER-CABLE recommended accessories should be
used with this product. A complete line of accessories is available from your PORTER-
CABLE Factory Service Center or a PORTER-CABLE Authorized Warranty Service
Center. Please visit our Web Site www.portercable.com for a catalog or for the name of
your nearest supplier.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE
• Unit will not start. • Cord not plugged in.
• Circuit fuse is blown.
• Circuit breaker is tripped.
• Cord or switch is damaged.
• Battery not charged.
For assistance with your product, visit our website at www.portercable.com for a list of service
centers, or call the Porter-Cable Customer Care Center at (888) 848-5175.
MAINTENANCE
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
THREE YEAR LIMITED WARRANTY
PORTER-CABLE will repair or replace, without charge, any defects due to faulty
materials or workmanship for three years from the date of purchase for tools (two years
for batteries). This warranty does not cover part failure due to normal wear or tool abuse.
For further detail of warranty coverage and warranty repair information, visit
www.portercable.com or call (888) 848-5175. This warranty does not apply to
accessories or damage caused where repairs have been made or attempted by others.
This warranty gives you specific legal rights and you may have other rights which vary in
certain states or provinces.
In addition to the warranty, PORTER-CABLE tools are covered by our:
1 YEAR FREE SERVICE: PORTER-CABLE will maintain the tool and replace worn parts
caused by normal use, for free, any time during the first year after purchase.
POSSIBLE SOLUTION
• Plug tool into a working outlet.
• Replace circuit fuse. (If the
product repeatedly causes the
circuit fuse to blow, discontinue
use immediately and have it
serviced at a Porter Cable service
center or authorized servicer.)
• Reset circuit breaker. (If the
product repeatedly causes the
circuit breaker to trip,
discontinue use immediately
and have it serviced at a Porter
Cable service center or
authorized servicer.)
• Have cord or switch replaced
at a Porter Cable Service
Center or Authorized Servicer
• Charge battery
7