THERMEx vertical 925 Instrucciones De Uso página 29

If the replacement and washing instructions are not followed,
the anti-grease fi lters may present a fi re hazard.
• The active carbon fi lters are used to purify the air which is
released back into the room.
The fi lters are not washable or re-usable and must be replaced
at least once every four months.
The active carbon fi lter saturation level depends on the fre-
quency with which the appliance is used, the type of cooking
performed and the regularity with which the anti-grease
fi lters are cleaned.
• Clean the cooker hood frequently, both inside and outside,
using a cloth which has been dampened with denatured
alcohol or neutral, non-abrasive liquid detergents.
• The light on the cooker hood is designed for use during
cooking and not for general room illumination.
Extended use of the light reduces the average duration of
the bulb.
• Replacing halogen light bulbs (Fig. 17).
In order to replace the dichroic lamps, carefully remove
the lamp from the lamp holder with the help of a small fl at
screwdriver or a similar tool. PLEASE NOTE! In doing this
operation, please take care not to scratch the hood.
Replace the bulbs with new ones of the same type.
• Commands: (Fig.18)
Push-button A = on/off lights switch
Push-button B = on/off cooker hood switch. The appliance
switches on at speed level 1, If the cooker hood is on depress
the push-button for 2 sec. to switch off the cooker hood. If
the cooker hood is at speed level 1 it will not be necessary
to depress the push-button to switch the cooker hood off.
Decreases the motor speed.
Display C = indicates the motor speed level selected and
activates the timer.
Push-button D = switches on the cooker hood. Increases the
motor speed. Touching the key at 3rd speed, the intensive
function runs for 10' , then the appliance go back to work at the
original speed. During this function the display blinks.
Key E = The Timer times the functions on activation for
15 minutes, after which they are switched off. The Timer is
deactivated by re-pressing Key E. When the Timer is activated
the decimal point must flash on the display. The Timer cannot
be activated if the intensive speed is functioning.
The "clean air" function is activated by pressing key E for 2
seconds when the appliance is switched off. This switches
the motor on for 10 minutes every hour at the first speed.
During functioning a rotary movement of the peripheral
segments must be visualised on the display. When this time
has passed the motor switches off and the fixed letter "C" must
be visualised on the display until the motor re-starts after 50
minutes for another 10 minutes and so on. Press any key apart
from the light keys to return to normal functioning. Press key
E to deactivate the function.
• Active carbon/grease filter saturation (Fig3):
- When display item C flashes, at a speed where it alternates
with the letter F (e.g. 1 and F), the grease filters must be
washed.
- When display item C flashes, at a speed where it alternates
with the letter A (e.g. 1 and A), the carbon filters must be
replaced.
After the clean filter has been positioned correctly, the
electronic memory must be reset by pressing button A for
approximately 5 seconds, until the indication F or A shown
on the display C stops flashing.
All manuals and user guides at all-guides.com
• Commands: (Fig.19)
Warning!
- When activating or deactivating the operations or the alarm,
the motor and lights must be switched off .
- This product is supplied with an acoustic indicator (buzzer).
Each time any button is pressed, this is confi rmed by an
acoustic indicator.
- This function can be deactivated or activated, by
simultaneously pressing the ON and TIMER buttons for fi ve
seconds.
- If your product is a FILTER version, it is necessary to activate
the active carbon fi lters indicator function which you fi nd in
the paragraph regarding this function.
Button A = light (Softlight)
Starting:
A brief pressure on the light button will turn on the light at the
maximum intensity, activating the fast softlight function.
Adjustment:
By keeping the light button pressed, the intensity can be
adjusted from maximum to minimum and viceversa.
Switching off :
Quick pressure of the light button.
Button B = OFF and Speed reduction
Adjustment:
A brief pressure of the OFF button will reduce the motor
speed. For example the indication on the display goes from
speed 3 to speed 2.
speed 3
speed 2
Switching off :
If the operating speed of the motor is set on level 1 of the
display, a brief pressure of the OFF button will switch off
the hood.
speed 1
If the OFF button is pressed for at least 2 seconds, regardless
from the selected motor speed, the hood will switch off .
OFF
Button C = Display
The display can alternate GREEN LEDs which indicate the
motor speed, with RED LEDs which indicate the alarm status
(See special functions).
speed 1
speed 2
speed 3
speed 4
- 29 -