Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Quick Start Guide
1. Remove the Shipping
Hardware
There are 4 screws, identified by red tags, that
secure the printer base to the inside mechanism,
and tie restraints that secure the Paper Stacking
Chains. The upper 2 shipping screws have wing-
heads which tighten a bracket against the platen to
prevent it from bumping
against the hammer bank.
The lower 2 shipping
screws fasten from
underneath, near the
front of the printer
cabinet. Remove all of
these restraints, including
the brackets beneath the
wing-head screws.
4. Install the Ribbon Cartridge
Step A. Open the printer lid. Remove slack in the new ribbon by turning the knob on the ribbon cartridge as indicated by the arrow printed
next to the knob.
Ribbon Cartridge
Step B. Carefully position the ribbon between the two panels of the ribbon shield.
All manuals and user guides at all-guides.com
2. Set Up Paper Stacking Chains
Paper exits the print area through a set of passive Paper Stacking Chains
that help fold and stack printed forms uniformly. Secure two of the
chains to the wire guide and two to the rear paper guide so that the
paper can be fed between them. Make sure chains are not tangled.
LG Series
Tractors
Hammer
Bank
Housing
Ribbon Cartridge
Step C. Press down lightly on the cartridge while turning the ribbon knob as before until it seats on
first the left, (as shown), and then the right cartridge drive posts. Make sure that the ribbon does
not twist or fold over.
Rear Paper Guide
Paper comes out between these two
sets of chains.
3. Connect the I/O and Power Up
Secure the cable to the printer interface using the correct connectors.
Shielded I/O cables must be used on all installations
to comply with regulatory requirements.
Serial Interface Port
Parallel Interface Port
Optional LAN
interface or
Optional Twinax/Coax interface
Shaft for
Tractors
On/Off Switch
& Power Plug
Publicidad
Resumen de contenidos para TallyGenicom LG Serie
- Página 1 All manuals and user guides at all-guides.com 2. Set Up Paper Stacking Chains Paper exits the print area through a set of passive Paper Stacking Chains that help fold and stack printed forms uniformly. Secure two of the chains to the wire guide and two to the rear paper guide so that the paper can be fed between them.
- Página 2 All manuals and user guides at all-guides.com 5. Loading Paper for Standard Printing Mode Paper Slot Step A. Raise the printer lid and open the doors on both tractors. Step B. Place the stack of paper inside the cabinet on the floor and feed the paper up through the paper slot, a little ways past the tractors and through the gap between the top back of the printer and the lid.
- Página 3 Papierstaplerketten, die dazu beitragen, dass die gedruckten Formulare gefaltet und gleichmäßig gestapelt werden. Befestigen Sie zwei Ketten an der Drahtführung und zwei an der hinteren Papierführung, so dass das Papier dazwischen laufen kann. Die Ketten dürfen nicht verwickelt sein. LG Serie Hintere Papierführung Kurzanleitung zur Inbetriebnahme 1.
- Página 4 Druckkopfabstand zu groß ist. Bei verschmiertem Druckbild ist der Druckkopfabstand zu klein. Wiederholen Sie Schritt G so oft, bis der Druck scharf und dunkel ist und keine Schmierspuren aufweist. 086253 - Kurzanleitung zur Inbetriebnahme für LG Serie...
- Página 5 Fixez deux chaînes au guide métallique et deux autres au guide de papier arrière pour que le papier puisse être correctement alimenté entre elles. Assurez-vous que les chaînes ne sont pas emmêlées. LG Serie Guide de papier arrière Guide d’installation rapide 1.
- Página 6 Examinez l’imprimé. Une impression faible indique un écart trop important et des traînées d’encre indiquent un écart trop faible. Recommencez l’Étape G jusqu’à ce que l’impression soit nette et noire sans traînée. 086253 – Guide d’installation rapide LG Serie...
- Página 7 Fissare due catene alla guida del filo e due alla guida posteriore della carta in modo da poter alimentare la carta fra LG Serie di loro. Accertarsi che le catene non siano aggrovigliate. Guida di riferimento rapido Guida posteriore della carta 1.
- Página 8 Esaminare lo stampato. Una stampa sbiadita indica che la distanza è troppo ampia, mentre macchie d’inchiostro indicano una distanza troppo ridotta. Ripetere il Passo G fino a che lo stampato non risulta nitido e scuro, senza macchie. 086253 - LG Serie - Guida di riferimento rapido...
- Página 9 All manuals and user guides at all-guides.com 2. Preparación de las cadenas de apilamiento del papel El papel sale del área de impresión a través de un conjunto de cadenas de apilamiento del papel que ayudan a doblar y apilar las hojas impresas uniformemente.
- Página 10 All manuals and user guides at all-guides.com 5. Instalación del papel para la modalidad de Ranura para el papel impresión estándar Paso A. Levante la tapa de la impresora y abra las puertas de ambos tractores. Paso B. Coloque la pila de papel dentro del gabinete en el piso y alimente el papel a través de la ranura, un poco más allá...