Tabla de contenido
Publicidad
13. Do not tilt lawnmower when the motor is running,
except when starting and stopping. In this case, do
not tilt more than absolutely necessary and lift only
the part which is away from the operator. Always
ensure that both hands are in the operating position
before returning the appliance to the ground.
14. Do not put hands near the grass discharge chute.
15. Never pick up or carry a mower when it is operating
or still connected to the mains supply.
16. Remove the plug from the mains :
-
before leaving the mower unattended for any period;
-
before clearing a blockage;
-
before checking, cleaning or working on the appliance;
-
if you hit an object. Do not use your lawnmower
until you are sure that the entire lawnmower is in a
Wheel Assembly
1. Insert wheel fixing bolt into the hub cap (A1)
2. Insert the hub cap plug into the hub cap until it clicks
into place (A2)
3. Locate the hub cap assembly through the wheel and
into the selected hole in mounting plate.(B) (See
'Cutting Height Adjustment' for correct height of cut)
4. Turn the wheel hub in a clockwise direction until the
wheel assembly is securely located to the deck. (C)
Assembly of Lower Handles to Deck
1. Insert each side of the lower handles into deck as
shown in Fig D.
2. Push each side of the handle firmly down until it is
located securely into the deck (E).
3. Insert the screws into holes using a pozidrive
screwdriver and tighten fully into deck as shown in
Fig E.
Fitting Fully Assembled Grassbox to Lawnmower.
See Fig J.
1. Lift safety flap.
2. Make sure the discharge chute is clean and free
from debris.
3. Locate fully assembled grassbox onto the location
point at the rear of the deck (J1)
4. Locate safety flap onto the top of the grassbox.
Ensure the grassbox is securely located.
Cutting Height Adjustment (K)
•
Height of cut is adjusted by raising or lowering
the wheels.
•
There are five heights of cut on this product.
•
NOTE
A medium height of cut is recommended for
most lawns.
The quality of your lawn will suffer and
collection will be poor if you cut too low.
ENGLISH - 2
All manuals and user guides at all-guides.com
Safety Precautions
Assembly Instructions
Grassbox
Adjusting the Cutting Height
safe operating condition.;
-
if the lawnmower starts to vibrate abnormally.
Check immediately. Excessive vibration can cause
injury.
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be sure the
lawnmower is in safe working condition.
2. Check the grassbox/grassbag frequently for wear or
deterioration.
3. Replace worn or damaged parts for safety.
4. Only use the replacement blade, blade bolt, spacer
and impeller specified for this product.
5. Be careful during adjustment of the lawnmower to
prevent entrapment of the fingers between moving
blades and fixed parts of the machine.
Assembly of Upper Handles to Lower Handles.
1. Insert the nuts into the upper handle wing knobs.
(F1)
2. Ensure the upper handle is located correctly with the
lock-off button on the switchbox uppermost.
3. Ensure the upper handle and the lower handle are
aligned correctly. (F)
4. Fit the bolts, washers and wing knobs. (F)
5. Fit the cable to the handles with the clips provided,
making sure the cables are not trapped between the
upper and lower handles.
Grassbox Assembly.
1. Insert the grassbox handle into the grassbox upper, as
illustrated in fig G, and press firmly down until the
handle clicks into place - (if applicable).
2. Position the two grassbox halves together and press
each location point (H1) into position without fully
connecting the clips. When the location points are
matched correctly firmly press the grassbox together
until all clips are securely connected.(H)
• IMPORTANT !
AFTER FITTING ENSURE NO GAP REMAINS
BETWEEN THE SAFETY FLAP AND THE
GRASSBOX.
• Removal is the reverse procedure.
• For larger areas of grass where grass collection is
not required you can use your lawnmower without
the grassbox. Ensure the Safety Flap is fully closed.
The design of the safety flap permits the cut grass to
be discharged downward behind the machine.
HEIGHT OF CUT
Low
Low to Medium
Medium
Medium to High
High
WHEELS POSITION
Front position 1
Back position 1
Front position 1
Back position 2
Front position 2
Back position 2
Front position 2
Back position 3
Front position 3
Back position 3
Publicidad
Tabla de contenido
