Rampage AV-990 Manual De Operación página 7

1. Tune in a weak station around 1400 KHz on the
AM band.
2. Push the tape door open and locate the antenna
trimmer at the back of the cassette deck.
3. Using a small screwdriver, slowly adjust the
trimmer for maximum output from the radio.
NOTE: The Antenna Trimmer only affects AM
reception, and will have no effect on FM
reception. The trimmer only needs to be
adjusted when the radio is first installed
and at any time a change is made to the
vehicle antenna (replacing the mast, etc.).
9
DISPLAY PANEL
The digital display of the radio frequency and time
are shown on this panel as well as indicators for AM,
FM, and stereo reception.
bl
CASSETTE DOOR
Hold the cassette with the exposed tape edge to the
right and insert it into the cassette door. Depress
fully until the cassette is engaged and begins play-
ing. When the cassette reaches the end of the side
of the tape being played, the unit will automatically
change direction of play, as shown by the Tape
bp
Direction Indicators ,andplaytheothersideofthe
cassette.
bm
FAST-FORWARDBUTTON(FF)
Pushing the Fast-Forward button will cause the tape
to move rapidly in the forward direction of play. To
stop Fast-Forward movement, lightly push the Re-
bn
wind button until the Fast-Forward button disen-
gages.
bn
REWINDBUTTON(REW)
Pushing the Rewind button will cause the tape to
move rapidly in the reverse direction of play. To stop
Rewind movement, lightly push the Fast-Forward
bm
button until the Rewind button disengages.
1. With the vehicle ignition switch "on", turn the unit off or insert a cassette into the tape door so that the
time is showing on the display panel.
2. Using a toothpick, pen point or similar thin object, press the Hour Adjust button
to the correct setting.
3. Using a toothpick, pen point or similar thin object, press the Minute Adjust button
minutes to the correct setting.
All manuals and user guides at all-guides.com
bo
To manually reverse tape direction and play the
other side of the cassette, lightly push both the Fast-
Forward
time. The change of direction will be shown by the
TapeDirectionIndicators
bp
These arrows show the direction of tape play and will
change when the program is changed either auto-
matically at the end of play on one side of the
cassette or manually by the Program Selector
bq
Tape playback is stopped and the cassette is ejected
by pressing this button, which also has the function
of switching over to radio operation.
NOTE: Never leave a cassette engaged in the
br
During radio operation, the station frequency will be
shown on the display panel. Pressing this button will
cause the time to be displayed for 5 seconds before
returning to frequency read-out.
During cassette operation, the time will always be
shown on the display panel.
bs
This button is used to adjust the hours on the built-
in quartz clock. The button is recessed to prevent
accidental engagement so a toothpick, pen point or
similar object should be used to activate it.
bt
This button is used to adjust the minutes on the built-
in quartz clock. The button is recessed to prevent
accidental engagement so a toothpick, pen point or
similar object should be used to activate it.
SETTING THE CLOCK SETTING THE CLOCK
SETTING THE CLOCK SETTING THE CLOCK SETTING THE CLOCK
PROGRAMSELECTOR
bm bn
and Rewind
bp
.
TAPEDIRECTIONINDICATORS
EJECT BUTTON ( )
player when not in use. Doing so can cause
damage to the cassette and/or mechanism.
Always press the eject button and remove
the cassette when leaving the vehicle.
DISPLAY CALL SELECTOR (CALL)
HOUR ADJUST BUTTON (H)
MINUTE ADJUST BUTTON (M)
bs
buttons at the same
bo
.
to adjust the hours
6 6 6 6 6
bt
to adjust the