Swing-N-Slide TB 1543 Instrucciones De Montaje

KIT INCLUDES:
QTY DESCRIPTION
1 Swivel
2 6-1/2'' Carriage Bolt
2 Washer
2 Loc Nut
1 Swing Assembly
8 1-1/4" Screws
2 Beam Clamps
INSTALLATION:
1. Determine swivel location. It is recommended that the swing be placed in a swing bay on its own. If
needed the A-Frame on your existing swing set can be moved to create this space. The
A-Frame should be approximately 42" from the end of the swing beam. The Swing Assembly shall
have a minimum clearance of 24" from any structural element. See (Fig. 1 & 2) for completed
assembly with A-Frame change.
2. Position swivel so that it is centered on the UNDERSIDE of the beam at the proper location.
See (Fig. 1), dimensions stated are to be used as a guide for swivel placement.
3. Using the swivel as a template, mark hole locations on the UNDERSIDE of the beam and drill a 5/16"
hole through the beam. NOTE: Drill holes at 90 degrees to the beam. If drill bit is not long enough,
measure and mark the top of the beam and drill from both sides.
4. Insert (2) 6-1/2" carriage bolts through the mating holes in the beam. NOTE: It may be necessary to
force the carriage bolt through the beam with the aid of a hammer. Secure beam clamps using
(4) 1-1/4" screws. Place the swivel on bottom side of the swing beam aligning holes with the carriage
bolts. Secure with a washer and loc nut. Tighten loc nuts securely. (Fig. 3).
NOTE: Periodically check hardware for tightness, and tighten as necessary. Check all moving parts
such as swivel, connecting links and rope for wear and replace immediately if necessary.
5. Slip (3) Quick Links onto swivel and tighten with an appropriate wrench, as shown in (Fig. 2a).
SEAT ADJUSTMENT:
1. To Adjust Your Seat Height: Flip over your seat and pull on the looping segment to loosen the
suspending rope as shown in (Fig. 2b). Repeat on all three sides.
2. Adjust your ropes on all three sides so that your seat is sitting level at the height appropriate for your
child, as shown in (Fig. 2c).
3. Pull up on the segment suspending the seat and down on the segment suspending the foot platform
to sinch the rope binding tight, as shown in (Fig. 2d).
4. Make certain the seat is secure before you allow your child to use the swing.
Slip (3) Quick Links
Onto Swivel and
Tighten With An
Appropriate Wrench.
Fig. 2b
Note: All swing sets must be anchored in at least four locations prior to using the
Swing. Two anchors should be placed on the A-Frame nearest the Swing and two
on the slide platform/tower.
© Swing•N•Slide Corp. 2012
EL JUEGO INCLUYE:
CANTIDAD DESCRIPCIÓN
1
Eslabón giratorio
2
Pernos de carrocería
de 6-1/2" (16.5 cm)
2
Arandelas
2
Contratuercas
1 Oscilación de la Asamblea
8 Tornillos de 1-1/4" (3.18 cm)
2 Abrazaderas de Vigas
Fig. 2c
TB 1543
TB 1543
L'ENSEMBLE COMPREND :
QUANTITÉ DESCRIPTION
1
Pivot
2
Boulons à carrosserie de
6-1/2 po (165 mm)
2
Rondelles
2
Contre-écrous
1 Assemblée swing
8 Vis de 3,2 cm (1 1/4 po)
2 Serre-poutres
Fig. 2a
Fig. 2d
Printed in U.S.A.
NE 4963
NE 4963
Fig. 1
Fig. 2
LA 6498