Display Light; Night Light; Troubleshooting - TFA TIME & LIGHT 60.2029.10 Instrucciones De Uso

Alarm clock function
Press the ALARM 1 (Fig.1-H) or ALARM 2
alarm time will be displayed for a short moment. The corresponding alarm symbol flashes.
Alarm time setting
Press and hold the ALARM 1 (Fig.1-H) button in normal mode to enter the alarm setting mode.
The hour digit and the alarm symbol 1
Press the or button (Fig.1-E, Fig.1-K) to set the hours.
Confirm the setting with the ALARM 1 button.
Set the minutes in the same way.
Confirm the setting with the ALARM 1 button.
ALARM 2 can be adjusted in the same way.
Activate and deactivate the alarm
Press the ALARM 1 (Fig.1-H) or ALARM 2
normal mode.
The alarm is activated. The corresponding alarm symbol
permanently on the display.
Press again the ALARM 1 or ALARM 2 button to deactivate the alarm. The alarm symbol disappears.
When the alarm is activated, the alarm starts to ring when the set alarm time is reached. The
backlight turns on.
Press any button or flip over the alarm clock to stop the alarm.
If the alarm is not stopped manually, the ascending alarm tone automatically turns off after 3
minutes and it will be reactivated at the same set time on the following day.
When the alarm goes on, activate the snooze function by shaking it with a quick,
lateral movement.
The snooze symbol (Fig.1-L) will appear on the display.
The alarm will be interrupted for 5 minutes.

Display light

The backlight is activated by a sensor that reacts to vibrations, e.g., by lifting and setting
down the device.
Alternatively, press any button. The backlight turns on for ten seconds.
In normal mode, press or button (Fig.1-E, Fig.1-K) button to adjust the brightness in 3 steps
or switch off the backlight completely (OFF - LOW - MIDDLE - HIGH).
From 9 p.m. to 7 a.m., a permanent backlight automatically switches on at the set brightness level.
Note: If the brightness is set to "OFF", the automatic backlighting at night is also switched off.
12
(Fig.1-G) button in normal mode. The last adjusted
(Fig.1-J) start blinking.
(Fig.1-G) button twice in quick succession in
| (Fig.1-J|Fig.1-F) appears

Night light

Press the LIGHT button (Fig.1-B) twice in quick succession in normal mode.
The night light symbol (Fig.1-C) appears on the display. The function is activated.
Flip over the alarm clock to turn on the night light. The night light faces up.
In this position you can now use the
to 7 different levels.
To turn off the night light, flip over to the alarm clock side. The digital alarm clock faces up again.
To deactivate the night light function, press the LIGHT button twice in quick succession in normal
mode. The night light symbol disappears.

Troubleshooting

Problem:
No display on the device
Incorrect indication
Device makes a noise when shaken
or flipped over
If your device fails to work despite these measures, contact the retailer where you purchased the product.
Specifications
Power consumption:
Capacity / Energy:
Charging power source:
Accessories:
Charging time:
Battery runtime:
Housing dimension:
Weight:
or button (Fig.1-E, Fig.1-K) to set the brightness
Solution:
Charge the device via micro-USB cable (incl.)
Press the RESET button (Fig.2-B) for 3 seconds
using a pin
Not a malfunction! The device has a ball switch
that may make a slight noise when the ball rolls
around.
Built-in Li-Ion rechargeable battery
1200 mAh
Micro-USB 5V DC | max. 500mA
Charging cable (USB to Micro-USB)
Approx. 3-4 hours
Up to 200 hours (depending on the light level)
81 x 115 x 93 mm
159 g (device only)
13