Connection Valve Assembly; Filling Pool; Pool Maintenance; Repair - Bestway Roal Frame Pool Manual De Instrucciones

Ocultar thumbs

página de 28

/ 28
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

1. Screw the Debris Screen onto the Connector. (See Fig.9)

2. From inside the pool liner, insert this assembled Unit to the pool's inlet A and outlet B. (See Fig.10)

NOTE: Ensure the Gasket is properly in place on the assembled Unit inside of the pool liner.

3. From outside of the pool, tighten Connector Nut onto the assembled Unit by the wrench. (See Fig.11)

4. Hand-tighten the Control Valve to the assembled Unit. (See Fig.12)

NOTE: Check that both the Control Valve Gasket and O-ring are correctly positioned on the Control Valve.

OPERATION NOTE: Use the control screw on top of the Control Valve to open and close the Valve. (See Fig.13)

5. Make sure the valve is closed.

Fig. 9

Fig. 10

Pool Outside

ATTENTION: Do not leave pool unattended while filling with water

1. Ensure drain valve is firmly closed. Fill 1inch to 2inch water in the pool to cover the floor. Gently smooth out all wrinkles from the center of the pool liner outwards

to the pool walls.

2. Fill pool to drain valve.

STOP

3. Turn water off. Check that the water is not collecting on any side to ensure the pool is level, drain water and re-level ground by digging out (See Fig.16) Never

attempt to move the pool with water in it, serious personal injury or damage to the pool may result.

NOTE: Your pool may contain up to xxxx liters / xxxx gallons which equals xxxx pounds of pressure. (According to dimensions showed on package). If your pool

has any bulge or uneven side then the pool is not level, the sides may burst and the water may discharge suddenly causing serious personal injury and/or

damage to property.

4. When level, fill pool to lowest pump valve.

STOP

5. Turn water off. Check valves for secure fit.

6. Fill pool until water capacity is 90%. DO NOT OVERFILL as this could cause the pool to collapse. In times of heavy rainfall you may need to empty some of the

water to ensure the level is correct. (See Fig.15)

7. Check pool for any leaks at valves or seams, check ground cloth for any evident water loss. Do not add chemicals until this has been done.

8. In the event of a leak, patch your pool liner using the patch kit provided. Refer to the FAQ's for further information.

Fig. 14

If you do not adhere to the maintenance guidelines below, your health might be at risk, especially that of your children.

NOTE: The filter pump is used to circulate the water and to filter small particles to keep your water free from suspended dirt particles. In order to keep your pool

water clean and hygienic you must add chemicals.

To keep your pool clean:

1. Contact your local pool supply shop for advice and purchase of chemicals and PH kits. One of the most important factors to increase the life of the liner is to keep

continuously clean and healthy water. Please follow strictly the instructions from professional technicians for the water treatment through the use of chemicals.

2. Locate a bucket of water next to pool to clean users' feet before entering pool.

3. Cover the pool when not in use.

ATTENTION: THE BESTWAY POOL COVER IS NOT A SAFETY COVER.

4. Skim pool regularly to avoid settled dirt.

5. Gently clean any scum from the side with a clean cloth.

6. To improve the water quality we suggest using Bestway accessories like skimmer, maintenance kits. Please be careful in case of rainwater, kindly check that the

water level is not higher than the expected one. If so, please act consequently.

Proper maintenance can maximize the life of your pool.

ATTENTION: Ensure you run your filtration system everyday for 7-8 hours. Do not use pump when pool is in use.

If your pool liner is damaged, use a repair patch. See FAQ's instructions.

All manuals and user guides at all-guides.com