Emc Information; Maintenance And Repairs; Safety And Performance Standards - Duronic SADV1 Manual De Instrucciones

EMC information

Warning: Use of this appliance adjacent to or stacked with other device
should be avoided because it could result in improper operation. If such use
is necessary, this appliance and the other device should be observed to verify
that they are operating normally. If the appliance does not light on or flickering,
it means that the appliance is not operating normally.
Warning: Do not change any cable without authorization of the manufacturer.
Use of cables other than those specified or provided by the manufacturer of
this appliance could result in increased electromagnetic emissions or de-
creased electromagnetic immunity of this appliance and result in improper
operation.
Warning: Don't near active HF surgical equipment and the RF shielded room
of an ME system for magnetic resonance imaging, where the intensity of EM
disturbances is high.
Warning: Portable RF communications equipment (including peripherals such
as antenna cables and external antennas) should be used no closer than 30
cm to any part of this appliance, including power cable. Otherwise, degrada-
tion of the performance of this equipment could result.
If the appliance does not light on or flickering due to the electromagnetic dis-
turbances, do not use it and try to place the appliance in other location.
For maintaining the basic safety and essential performance with regard to
electromagnetic disturbances for the expected service life, please precaution
to take if the use location is near (e.g. less than 1,5 km from) from AM, FM or
TV broadcast antennas.

Maintenance and Repairs

• Avoid exposing the screen to direct sunlight,
spotlight or any other heat source.
• Do not use alcohol or ammonia base liquid to clean the screen.
• The cleaning information provided in the section "Cleaning".
• Please do not attempt to repair the appliance yourself. This could result in
serious injuries. Failure to observe this regulation shall void the warranty.
• If this appliance is damaged in any way or it is not working, it should not
be operated. Please try to fix the problem according to FAQ table.
If the problem is still not resolved, please contact customer service or the
dealer, since special tools are needed to make repairs.
Never try to repair the appliance yourself.
8

Safety and performance standards

The "Daylight" has been designed and manufactured to conform
to the highest standards of safety and performance including
electromagnetic compatibility (EMC).
The "Daylight" conforms to the applicable requirements of the following:
This appliance meets the requirement of Medical Device
Directive 93/42/EEC for medical appliances.
The appliance is complied with the following emission and immunity standard,
and test level:
Emissions Test Standard
RF emissions CISPR 11
Harmonic emissions IEC 61000-3-2
Voltage fluctuations/ flicker
emissions IEC 61000-3-3
Guidance and manufacturer's declaration - electromagnetic Immunity
Test Band
Radiated RF
Frequency (MHz)
IEC61000-4-3
(MHz)
(Test specification for
ENCLOSURE PORT
385 380 - 390
IMMUNITY to
RF wireless
communications
equipment)
450 430 - 470
710 704 - 787
745
780
810 800 - 960
870
930
1720 1700
1845 - 1990
1970
2450 2400
- 2570
5240 5100
5500 - 5800
5785
Compliance
Group 1, Class B
Class A
Comply
Service Modulation Modulation Distance
(W) (M)
TETRA 400 Pulse 1.8 0.3
modulation
18Hz
GMRS 460 FM 2 0.3
FRS 460 + kHz
deviation
1 kHz sine
LTE Band Pulse 0.2 0.3
13,17 modulation
217 Hz
GSM Pulse 2 0.3
800 / 900 modulation
TETRA 800 18Hz
iDEN 820
CDMA 850
LTE Band 5
GSM 1800 Pulse 2 0.3
CDMA 1900 modulation
GSM 1900 217 Hz
DECT;
LTE Band
1, 3, 4, 25;
UMTS
Bluetooth Pulse 2 0.3
WLAN, modulation
802.11 b/g/n, 217 Hz
RFID 2450
LTE Band 7
WLAN Pulse 0.2 0.3
802.11 modulation
a/n 217 Hz
9
Immunity
Test Level
(V/M)
27
28
9
28
28
28
9