VXI VEHS-A1 Guia De Inicio Rapido

203425C_VEHS-A1_User_Guide_102913:Layout 1
*This user guide describes the installation steps to connect the VEHS to your phone. For information about your
phone's capabilities or provisioning requirements go to www.vxicorp.com/resources/vehs, visit your phone system
manufacturer's website, or contact your IT administrator.
*Le manuel de l'utilisateur décrit les étapes de branchement du VEHS à votre téléphone.Pour des
renseignements sur les capacités de votre téléphone ou sur les exigences en matière d'approvisionnement, visitez le
www.vxicorp.com/resources/vehs ou le site Web du fabricant de votre téléphone, ou communiquez avec votre
administrateur TI.
*Esta guía de usuario describe los pasos de instalación para conectar el VEHS a su teléfono.Para obtener información
sobre las capacidades de su teléfono o requerimientos de provisiones visite www.vxicorp.com/resources/vehs, visite
el sitio web del fabricante del sistema de su teléfono o comuníquese con su administrador TI.
VXi Corporation | 271 Locust Street, Dover, NH 03820 USA
Toll Free | Sans frais | Número gratuito: (800) 742-8588
Phone | Téléphone | Teléfono: 1 603 742-2888
© 2013 VXi Corporation. All other trademarks are property of their respective owners.
Printed in China | Imprimé en Chine | Impreso en China
All manuals and user guides at all-guides.com
10/29/13 1:03 PM Page 1
www.vxicorp.com
APN 203425C
INSTALLATION
1. Remove the panel from the bottom of 4. Connect the longer VEHS-A1 cable
the base station (refer to the V150 into the headset port of the phone
User Guide for additional information). (the headset port is generally located
on the bottom of the phone).
2. Attach the VEHS-A1 to the bottom of
the V150 by carefully inserting the
plastic guide pin into the screw-hole
socket on the base of the V150, then
press together the rear of the V150
base and VEHS-A1 until it snaps
into place.
5. Insert the 2.5 mm microphone con-
nector into the 'microphone' jack of
the VEHS-A1. Affix the microphone to
the phone's speaker grill by carefully
removing the paper backing from the
adhesive ring on the microphone
housing and placing the microphone
over the grill; the hole of the micro-
3. Insert the color-coded cables from
phone housing should line up with
the VEHS-A1 into the corresponding
one of the center slots of the grill.
color-coded jacks of the V150 base
station; the connectors should 'snap'
in place when fully inserted.
EHS/LIFTER POWER TEL WALL BASE JACK HANDSET
JACK
VXi LIMITED WARRANTY
1. VXi warrants that your product will be free from defects in material and workmanship for one year from
the date of purchase. If, during that period from the date of purchase, your product fails to work due to
a defect in material or workmanship, VXi will repair or replace the product, at its election, free of charge.
Without proof of purchase, the warranty period begins on the date of manufacture. Consumable
components (for example, cushion, battery and fuse) are not included in this warranty.
2. The foregoing limited warranty does not cover equipment failure attributable to accident, improper operation,
misuse, abuse, or any cause other than defects in the materials or workmanship of VXi's products.
3. VXi's obligations under this warranty are limited to repair or replacement (at our option) of any defective part
returned to VXi at the customer's expense. Returned products require a Return Authorization that may be
obtained by calling 800-742-8588. Products returned to VXi for repair under this warranty will be return
shipped to the customer at VXi's expense.
4. THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions
do not permit the exclusion of implied warranties and the foregoing exclusions may not apply to you.
5. In no event shall VXi be responsible for any other damages whatsoever, including direct, indirect, special,
incidental, consequential, or other damages for breach of this or any other warranty, express or implied.
6. Setting the microphone sensitivity.
a. Adjust the phone's ringer volume
to the desired level.
b. Place a test call to the phone.
As the phone is ringing, rotate the
VEHS-A1's 'Microphone Sensitivity'
thumb wheel until a ring-tone is
heard in the V150 headset.
ABCDEFG
Additional V150 Setup
- V150 should be in MODE 2.
- V150 'Compatibility Switch' should be
placed in the 'D' position.
LED Status Indicator
The LED status indicator indicates the
phone's mode as shown by the table
below.
MO
DE
MESSAGE
Phone Mode LED indicator
CONTACTS
1
On-hook
4
Off-hook Slow flash
7
Incoming ring detected
Solid on
Fast flash