Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Important Safeguards:
WARNING – When using electrical equipment, basic safety precautions should always be used including the following:
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and
operation of the product and the hazards involved.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
Mark means lamp contains mercury.
Hg
Hg
Follow disposal laws.
See www.lamprecycle.org
Slipfitter
❶
Disconnect Power
• Always disconnect power during
installation and maintenance.
➋
Mount Fixture
⑤
• Slide slip fitter
over top of pole.
• Remove cover from slipfitter wiring
⑨
chamber
.
• Aim fixture on the horizontal and
⑧
tighten slip fitter bolts
.
• Adjust the fixture tilt. Ensure that
⑥
the teeth
of the slip fitter are in
alignment, then tighten the knuckle
⑦
bolt
. Do not over tighten the
⑦
knuckle bolt
.
(Do not exceed 30 Ft/Lbs
maximum torque) .
• Loosen the cover screws to open
hinged door assembly
• Open ballast cover.
• Pull supply cable
➌
Check Voltage
•
When fixture is pre-wired standard is: USA 277V – Canada 347V
•
Ensure your voltage is correct.
• If necessary, connect wires to proper voltage.
• Individually cap all unused leads.
• Replace cover.
❹
Install Lamp
• Install lamp.
• Close hinged door and secure cover screws.
SAVE THESE INSTRUCTIONS
®
Technical Support: 888 / 387-2212
1300 S Wolf Road, Des Plaines, Illinois, 60017 / 219 Shoemaker Street, Kitchener, Ontario, N2E 3B3 / 220 Chrysler Drive, Brampton, Ontario L6S 6B6
ACCUFLOOD
Installation instructions for Yoke and Slippfitter mount
Series "EF", "NF" "FLM" and "FLC" Installation Instructions
⑤
⑧
Slipfitter bolts
⑨
⑦
⑥
⑧
⑤
Slipfitter
bolts
™
Yoke Mount
❶
Disconnect Power
• Always disconnect power during
installation and maintenance.
➋
Mount Fixture
①
• Secure fixture yoke
to mounting
bracket.
• Loosen yoke bolts and set screws
then aim fixture at desired point.
• Tighten yoke bolts and set screws
• Loosen the cover screws and open
hinged door assembly.
• Open ballast cover.
• Pull supply cable through cord
④
connector
.
④
• Tighten cord connector
.
➌
Check Voltage
•
When fixture is pre-wired standard is: USA 277V – Canada 347V
•
Ensure your voltage is correct.
• If necessary, connect wires to proper voltage.
• Individually cap all unused leads.
• Replace cover.
❹
Install Lamp
• Install lamp.
• Close hinged door and secure cover screws.
Z-12026
Rev 3 15/07/2007
③
,
③
.
①
④
③
①
③
Publicidad
Manuales relacionados para AccuLite ACCUFLOOD Z-12026
Resumen de contenidos para AccuLite ACCUFLOOD Z-12026
- Página 1 Z-12026 ACCUFLOOD ™ Rev 3 15/07/2007 Installation instructions for Yoke and Slippfitter mount Series “EF”, “NF” “FLM” and “FLC” Installation Instructions Important Safeguards: WARNING – When using electrical equipment, basic safety precautions should always be used including the following: This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
- Página 2 Accuflood Z-12026 Avec montage à chape ou à raccord lisse Rev 3 15/07/2007 Instructions d'installation pourlesa sérise “EF”, “NF” “FLM” et “FLC" Mises en garde importantes : L'utilisation de tout appareil électrique nécessite certaines précautions, notamment les mesures de sécurité suivantes : Ce produit doit être installé...
- Página 3 Trouble Shooting Guide First, check for physical damage to the luminaire. If it appears to be in good condition follow the following steps: Warning – Disconnect power: Always disconnect power during installation and maintenance. Lamp does not start or is slow to start Short Lamp Life Lamp Turns on &...