Additional Safety Instructions - Scheppach DECO-XLS Manual De Usuario

- Damaged switches have to be replaced by a
customer service workshop.
- Do not use any electric tool on which the
switch cannot be switched on and off.
21. ATTENTION
- The use of other insertion tools and other ac-
cessories can entail a danger of injury.
22. Have your electric tool repaired by a quali-
fied electrician
- This electric tool conforms to the applicable
safety regulations. Repairs may only be per-
formed by an electrician using original spare
parts. Otherwise accidents can occur.
WARNING
This electric tool generates an electromagnetic field
during operation. This field can impair active or passive
medical implants under certain conditions. In order to
prevent the risk of serious or deadly injuries, we recom-
mend that persons with medical implants consult with
their physician and the manufacturer of the medical im-
plant prior to operating the electric tool.

5.2 Additional safety instructions

• Switch the machine off immediately and pull the
power plug in an emergency.
• Follow all these safety instructions before and while
working with the saw.
• Do not use this saw to cut fire wood.
• Do not use this saw to cross-cut roundwood without
a suitable holding device.
• The machine is equipped with a safety switch to
prevent it from being switched on again accidentally
after a power failure.
• If you need to use an extension cable, make sure
its conductor cross-section is big enough for the
saw's power consumption. Minimum cross-section
1,5 mm .
2
• If you use a cable reel, the complete cable must be
pulled off the reel.
• Persons working on the machine should not be dis-
tracted.
• After you have switched off the motor, never slow
down the saw blade by applying pressure to its side.
• Only fit blades which are well sharpened and have
no cracks or deformations.
• Faulty saw blades must be replaced immediately.
• Never use saw blades which do not comply with the
data specified in this manual.
28 | GB
• It is imperative to make sure that all devices which
cover the saw blade are in good working order.
• Never dismantle the machine's safety devices or
render them inoperative.
• Damaged or faulty safety devices have to be re-
placed immediately.
• Never cut workpieces which are too small to hold
securely in your hand.
• Never load the machine so much that it cuts out.
• Always press the workpiece firmly against the saw
table.
• Never remove loose splinters, chips or jammed piec-
es of wood when the saw blade is running.
• Switch the machine off to rectify faults at the blocked
plug-in tool. - Pull the power plug- Remove the
blockage. Important! Risk of injury from saw blade!
Wear gloves. Carry out a trial run without a work-
piece. Ensure that no unusual noise or vibration oc-
curs. Should this be the case, switch the unit off and
contact the manufacturer.
• Carry out retooling work, adjustments, measure-
ments and cleaning jobs only when the motor is
switched off. - Pull the power plug. -
• Before switching on, make sure that all keys and
wrenches have been removed from the tool.
• Switch off the motor and pull the power plug before
you leave the workplace.
• Electrical installation work, repairs and maintenance
may only be carried out by persons who have been
specially trained.
• Refit all guards and safety devices immediately af-
ter you have completed any repairs or maintenance
work.
• Be sure to observe the safety information and op-
erating and maintenance instructions issued by the
manufacturer, as well as the dimensions listed in the
Technical Data.
• It is imperative to observe the accident prevention
regulations in force in your area as well as all other
generally recognized rules of safety.
• Note the information published by your professional
associations (VBG 7).
• The saw is intended to be used indoors only.
• Workpieces that are smaller than the saw blade
guard can cause injuries to the hands or fingers.
Use suitable aids!
• Avoid cramped hand positions when guiding in the
workpiece and avoid positions in which slipping
could lead to your hand making direct contact with
the saw blade.
www.scheppach.com