OttLite L13516 Guia De Inicio Rapido

13w Clip-On Lamp
L13516 L13339
INS1 10013 REV05051 1
ENGLISH
CONGRATULATIONS!
You've purchased the finest in natural
lighting technology with your new
OttLite ® product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product
Registration Form and return it today
by mail, or register online by going to:
www.OttLite.com/warranty.
WARNING: To prevent electric shock,
make sure the lamp is not plugged in
until all assembly steps are complete.
LAMP ASSEMBLY
1. Make sure the lamp is not plugged into
an electrical socket.
2. Attach clip to table, shelf or other
strong, solid surface.
3. Plug lamp into a standard 120V sock-
et. Your lamp is ready for use.
4. Turn lamp on or off by depressing rock-
er switch on end of socket housing (A).
TUBE INSERTION/REPLACEMENT
1. Make sure the lamp is not plugged into
an electrical socket.
2. If the lamp has been in use, allow it to
cool for approximately 5 minutes before
proceeding.
3. Rotate the shade (D) so that the notch
in the base of the shade is positioned
over the tab (C) located on the socket
housing (A). Refer to the diagram for
proper shade position.
4. Remove the shade (D) by pulling it
straight out from the socket
housing (A).
GX7909 CAUTION!
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer
or its service agent or a similar qualified person in order to avoid a hazard. Indoor use only.
Clip-On Lamp
CAUTION! IMPORTANT SAFETY INSTRUCTIONS:
5. To install a tube in the socket (B),
grasp the tube firmly in your hand, posi- THIS PORTABLE LAMP HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER) AS A FEATURE TO
tion the tube so that it is aligned as pic-
REDUCE THE RISK OF ELECTRIC SHOCK. THIS PLUG WILL FIT IN A POLARIZED OUTLET ONLY ONE WAY. IF THE
tured in the diagram, then push the tube
PLUG DOES NOT FIT FULLY IN THE OUTLET, REVERSE THE PLUG. IF IT STILL DOES NOT FIT, CONTACT A
straight into the socket until it "snaps"
QUALIFIED ELECTRICIAN. NEVER USE WITH AN EXTENSION CORD UNLESS PLUG CAN BE FULLY INSERTED.
into place.
DO NOT ALTER THE PLUG.
6. To remove a tube already installed in
CAUTION:
the lamp, grasp it firmly in your hand
and pull it straight out of the socket (B).
FULLY INSERT.
Do not twist or turn the tube while
removing it from the socket.
7. To replace the shade (D), position it
as indicated in the diagram, then push it
back into the socket housing (A), making
¡ PRECAUCIÓN! INSTRUCCIONES DE SEGURIDAD
sure the shade "snaps" into place.
IMPORTANTES:
8. Rotate the shade (D) to the desired
position for use.
ESTA LÁMPARA PORTÁTIL TIENE UN ENCHUFE POLARIZADO (UNA DE SUS PATAS ES MÁS ANCHA QUE LA OTRA)
COMO CARACTERISTICA PARA REDUCIR EL RIESGO DE UNA DESCARGA ELÉCTRICA. ESTE ENCHUFE ENCAJARÁ EN
Please note that in operation, OttLite ®
tubes are not dimmable.
CUALQUIER TOMACORRIENTE POLARIZADO SOLO DE UNA MANERA. SI EL ENCHUFE NO CALZA COMPLETAMENTE
EN EL TOMACORRIENTE DÉLE LA VUELTA. SI AÚN NO ENCAJA, PÓNGASE EN CONTACTO CON UN ELECTRICISTA
Enjoy your OttLite ® Clip-On lamp!
CALIFICADO. NUNCA UTILICE UNA EXTENSIÓN A NO SER QUE EL ENCHUFE PUEDA SER TOTALMENTE
INSERTADO. NO ALTERE EL ENCHUFE.
This lighting system is designed for
use with OttLite ® tubes type (style
PRECAUCIÓN:
number PL13-E). Use of other prod-
ucts voids the warranty and may result
ENCHUFE CON LA RANURA ANCHA, INSERTE TOTALMENTE.
in damage to the lighting system.
For more information on purchasing
replacement tubes/bulbs please go to
www.OttLite.com/replacement13wtube
AVERTISSEMENT! IMPORTANTES DIRECTIVES DE
SÉCURITÉ:
CETTE LAMPE PORTATIVE EST MUNIE D'UNE FICHE POLARISÉE (UNE LAME PLUS LARGE QUE L'AUTRE). CE
DISPOSITIF DE SÉCURITÉ DIMINUE LE RISQUE DE CHOCS ÉLECTRIQUES PUISQUE LA FICHE NE S'INSÈRE DANS
LA PRISE QUE D'UN SEUL CÔTÉ. SI ELLE N'ENTRE PAS DANS LA PRISE, INVERSEZ-LA. SI ELLE N'ENTRE
TOUJOURS PAS, CONTACTEZ UN ÉLECTRICIEN QUALIFIÉ. N'UTILISEZ JAMAIS AVEC UNE RALLONGE SAUF SI
LA FICHE S'INSÈRE ENTIÈREMENT. NE MODIFIEZ PAS CE DISPOSITIF DE SÉCURITÉ.
AVERTISSEMENT:
DANS LA GRANDE FENTE ET POUSSEZ JUSQU'AU BOUT.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
PARA PREVENIR UNA DESCARGA ELÉCTRICA, HAGA COINCIDIR LA PATA ANCHA DEL
POUR ÉVITER LES CHOCS ÉLECTRIQUE, INSÉREZ LE BOUT LARGE DE LA FICHE