b) Store the machine in a dry place out of the reach of
children.
c) Always allow the machine to cool before storing.
d) When servicing the shredding means be aware that,
even though the power source is switched off due to
the interlock feature of the guard, the shredding
means can still be moved.
e) Replace worn or damaged parts for safety. Use only
genuine replacement parts and accessories.
f) Never attempt to override the interlocked feature of the
guard.
2.5 Additional safety instructions for units with
bagging attachments
Switch-off the machine before attaching or removing the
bag.
2. ASSEMBLY
WARNING! Risk of physical injury!
Cut injury when the impeller turns or the
product starts accidentally.
v Wait for the impeller to stop, disconnect the
product from the mains and use gloves before
you do assembly.
To assemble for blower use:
To fit the blower tube [ Fig. A1 ]:
NOTE: A safety switch will prevent the product from start-
1
ing if the blower tube
is not installed correctly.
1. Align the grooves on the blower tube
grooves on the blower outlet
1
2. Push the blower tube
onto the blower outlet
snaps into place.
The blower tube is secured to the blower outlet with the
tube release button
3
.
1
To remove the blower tube
3
ton
and pull out the blower tube
To fit the intake cover [ Fig. A2 ]:
NOTE: A safety switch will prevent the product from start-
4
ing if the intake cover
is not latched closed.
4
1. Put the intake cover
on the lower opening of the
garden blower and turn the intake cover
up to the stop (bayonet fastening).
2. Tighten the fastening screw
4
To remove the intake cover
4
turn the intake cover
anti-clockwise and remove it.
To assemble for vacuum use:
To fit the vacuum tube [ Fig. A3 / A4 ]:
WARNING! Do not use the vacuum
ß
tube
is fitted to the upper tube
6b
All manuals and user guides at all-guides.com
1
with the
2
.
2
until it
, push the tube release but-
1
at the same time.
4
clockwise
5
.
5
, loosen the fastening screw
6
unless the lower
ß
.
6a
2.6 Recommendation
The machine should be supplied via a residual current
device (RCD) with a tripping current of not more than
30 mA.
Additional safety warnings
Danger! Small parts could be swallowed during assembly
and there is a risk of suffocation from the polybag. Keep
infants away during assembly.
Warning! This product produces an electro magnetical
field during operation. This field may under some
circumstances interfere with active or passive medical
implants. To reduce the risk of serious or fatal injury, we
recommend persons with medical implants to consult
their physician and the medical implant manu facturer
before operating this product.
1. Align the seams of the lower tube
ß
ß
2. Push the tubes
/
6a
6b
engaged.
NOTE: A safety switch will prevent the product from start-
6
ing if the vacuum tube
6
3. Put the vacuum tube
garden vacuum and turn the vacuum tube
up to the stop (bayonet fastening).
4. Tighten the fastening screw
To remove the vacuum tube
5
screw
, turn the vacuum tube
remove it.
To attach the collection bag [ Fig. A5 ]:
NOTE: A safety switch will prevent the product from start-
7
ing if the elbow tube
is not installed correctly.
1. Align the grooves on the elbow tube
2
on the blower outlet
2. Push the elbow tube
7
snaps into place.
The collection bag is secured to the blower outlet with
the tube release button
3. Clip the collection bag
vacuum tube
6
.
To remove the collection bag
8
button
and pull out the elbow tube
time.
,
To attach the shoulder strap [ Fig. A6 ]:
For extra support when you use the product as a vacuum,
a shoulder strap is included with your product. Attach the
strap to the product before operation.
v Snap the hook onto the retainer
ß
and upper tube
6b
together until they are fully
is not installed correctly.
on the lower opening of the
6
clockwise
5
.
6
, loosen the fastening
6
anti-clockwise and
7
with the grooves
.
onto the blower outlet
2
until it
8
.
9
0
into both loops
on the
9
, push the tube release
7
at the same
q
.
ß
.
6a
5