Yokis E2BP Manual Del Usuario página 9

RADIO TRANSMITTERS
e2BP 5454402 2-channel flush-mounted transmitter
tLC2C 5454401 2-pushbutton remote control
tLM1t45 5454411 1-pushbutton wall-mounted remote control
tLM2t45 5454406 2-pushbutton wall-mounted remote control
tLM4t45 5454412 4-pushbutton wall-mounted remote control
POWER RANGE
E2BPP 5454413 2-channel flush-mounted POWER transmitter
2-channel flush-mounted POWER transmitter
E2BPPX 5454414
POWER with external aerial
E4BPP 5454427 4-channel flush-mounted POWER transmitter
E4BPPX 5454428 4-channel flush-mounted POWER transmitter with
external aerial
TLC4CP 5454425 4-pushbutton POWER remote control
TLC8CP 5454423 8-pushbutton POWER remote control
GALET8TP 5454424 8 pushbutton flat POWER remote control
1-pushbutton wall-mounted POWER remote
TLM1T45P
5454417
control
2-pushbutton wall-mounted POWER remote
TLM2T45P 5454419
control
4-pushbutton wall-mounted POWER remote
TLM4T45P
5454421
control
technical specifications:
- CR2032 Lithium battery (included)
- Battery life > 7 years
- Max. 4 receivers per transmitter button
- Operating temperature: from -10 to + 50°C
- IP54 protection
- Max. relative humidity 80%
- Frequency: 2,4 GHz
- Transmission: two-way
WARNING: Explosion risk if the battery is replaced with a battery other
than the referred one. Dispose of the used batteries as per local stan-
dards.
E2BP/E2BPP E4BPP
D I R E C T M O D E
1
Press the pushbutton to be connected on the
transmitter (E) 5 times**.
The transmitter LED will start flashing for 30
seconds, indicating that the system is waiting
for connection.
** Each press must last less than 0.7 seconds
2
Briefly press the pushbutton in the 'connect' hole
of the receiver (R) (on the front or the back of the
receiver) with the point of a pencil while the
transmitter LED is flashing.
The transmitter LED will stop flashing.
Warning: the receiver must be powered.
DIRECT MODE CENTRALISATION
A command can be centralised by repeating the same procedure on up to four receivers. In case that more
than 4 receivers should be driven, use the Radio Bus.
DS1054-009F
All manuals and user guides at all-guides.com
The E2BP/E2BPP/E4BPP may be wired behind pushbuttons (or switches) of any
model. Wiring both channels is not indispensable: a single pushbutton can be
used connected to a single channel.
Switches can be used instead of pushbuttons to drive Mtr2000er
receivers. In this case, switch 5 times rapidly (not 10!) instead of using the 5
press sequence. Repeat the connection procedure by pressing 5 times to use a
pushbutton again instead of the switch.
GB
all YoKiS transmitters are compatible with
(relays, dimmer and Shutter Modules).
radio raNGe:
Standard range:
• In the same room (< 100 m²)
• 50m in open range
(Range may be reduced by presence of metallic
elements, crossing of walls or partitions)
Power range:
• Inside 100m² apartments with perpendicular
crossing of main wall or ceiling
• 250m in open range
(Range may be reduced by presence of metallic
elements, crossing of walls or partitions)
radio traNSMiSSioN:
the transmitter Led lights up only if radio
transmission was successful.
Adding an intermediate receiver will allow to solve a
problem of insufficient range (see § "How to increase
the range").
the Led will light up on transmitters
only if radio transmission was successful
Simply repeat the same procedure
to delete a connection
P8
YoKiS receivers
GB ES