Safety Rules - Kyocera TJEP TF-18/30 E Manual De Instrucciones

TJEP TF-18/30 E electric GB
WARNING
Always follow basic safety instructions when using the tool.
Failure to follow all instructions listed below, may result in
electric shock, fire and/or serious personal injury.
Read carefully these instructions before use your tool and
save them.
Always follow the safety rules and instructions in this
manual. The manufacturer will not accept any responsibility
for damage caused by improper use of the stapler.
Before use, read all warnings and all instructions listed below.
Keep all these warnings and instructions for future reference.

SAFETY RULES

Requirements of EN 60745-2-16
General Safety Warnings for the electric tacker
ELECTRICAL SAFETY
• The plug of the electric tool must corresponds to the
used socket type. You should never modify the plug in
any way. Do not use electrical adapters with electric tools
equipped with grounding system
• Do not use electric tools when raining and do not use
in damp places.
• Never use the cable for carrying the tacker and do not
pull it to disconnect by the socket. Keep the cable away
from heat, oil, sharp edges or moving parts.
• If you can not avoid using an electric tool in a damp
place, use a power supply protected by a differential
switch (RCD). The use of a differential switch (RCD)
reduces the risk of an electric shock
WORKPLACE SAFETY
• Keep clean and well lighted the work area
• Do not operate power tools in explosive environment,
such as in presence of liquids, gases or dusts.
• Keep children and other people at a safe distance
during the operation of the electric tool.
PERSONAL SAFETY
• Do not get distracted during use, always check what
you are doing and use common sense when operating
electric tools. Do not use the electric tool when you
are tired or under the influence of drugs, alcohol or
medications. A moment of inattention while operating
electric tools may cause serious personal injury.
• Use personal protective equipment. Always wear eye
protection. Protection devices such as dust masks, non-
slip safety shoes, safety helmet or ear protection, reduce
the possibility of suffering personal injury.
• Do not shoot empty or accidentally. Make sure that the
switch is in the off position before connecting the tool to
the mains or battery packs, before taking it or transport
it. Carry electrical tools with your finger on the switch or
connect to the mains with the switch in the on position
can cause accidents.
• Do not overreach during the use. Always keep the
position and equilibrium. This allows better control of
the tool in case of unexpected situations
• Dress appropriately for the work that you are doing. Do
not wear loose clothing or jewelry. Keep hair collected.
Clothing and gloves must be kept away from the moving
4
parts of the products.
• If there are devices to be connected to installations
for the extraction and collection of dust, sure they are
connected and used in an appropriate manner. The use
of these devices can reduce problems with dust.
USE AND MAINTENANCE OF ELECTRIC TOOLS
• Do not force the use of the electric tool. Always
use an appropriate tool to perform the operation. The
proper use of the tool allows you to perform the work
with greater efficiency and safety within the limits and
parameters of recommended levels
• Do not use the power tool if the switch on and off
does not fire properly. Any power tool that can not be
controlled with the switch is dangerous and must be
subjected to repairs
• Disconnect the plug from the power supply and/or the
group of batteries of the power tool before making any
adjustments, changing the accessorizes or storing the
tool. These preventive safety measures reduce the risk
of accidentally starting of the electric tool .
• Store the unused tool out of the reach of children and
do not allow their use to inexperienced persons or who
doesn't know these instructions. The electric tools are
dangerous if used by inexperienced persons.
• Always carry out necessary maintenance on electric
tools. Check the possible incorrect assembly or locking
of moving parts, any possible breakage of the parts and
any other condition that may affect the operation of
electric tools. If damaged please repair the tools before
using it again. Many accidents are caused by the bad
maintenance of the tool
• Use the electric tool in accordance with these
instructions, consider the working conditions and the
work to be performed.
SUPPORT
• Have the power tool repaired only by qualified
technicians and use only original replacement parts. This
ensures the continued safety of the tool.
TACKER SAFETY WARNINGS
• Always assume that the tool contains fasteners.
Careless handling of the tacker can result in unexpected
firing of fasteners and personal injury.
• Do not point the tool towards yourself or anyone
nearby. Unexpected triggering will discharge the fastener
causing an injury.
• Do not actuate the tool unless the tool is placed firmly
against the workpiece. If the tool is not contact with the
workpiece, the fastener may be deflected away from
your target.
• Disconnect the tool from the power source when the
fastener jams in the tool. While removing a jammed
fastener, the tacker may be accidentally activated if it
plugged in.
• Use caution while removing a jammed fastener. The
mechanism may be under compression and the fastener
may be forcefully discharged while attempting to free
a jammed condition. When fastening electrical cables,
make sure the cables are not energized.
Hold the tacker only by insulated gripping surfaces. Use
only fasteners designed for electrical cable installations.