Technical Data; Before Starting The Equipment - EINHELL GE-CH 18/60 Li Manual De Instrucciones Original

4. Technical data

Cutter rail length ..................................... 670 mm
Cutting length ......................................... 600 mm
Tooth spacing ........................................... 22 mm
Cuts/min. ..................................................... 2400
Sound pressure level L
Sound power level L
WA
Uncertainty K / K .............................. 3 dB (A)
pA WA
Sound power level guaranteed L
Vibrations a ............................................3.4 m/s
h
Uncertainty K ..........................................1.5 m/s
Caution
The equipment is supplied without batteries and
without a charger. It must only be used with the li-
thium-ion batteries in the Power-X-Change series.
The lithium-ion batteries of the Power-X-Change
series must only be charged only with the Power-
X charger.
The noise generated by the unit can exceed 85
dB (A). The operator will require noise protection
measures if this is the case. The noise emitted by
the hedge trimmer was measured in accordance
with EN 60745-1. The vibration emission level at
the handle was determined in compliance with
EN 60745-1.
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Anl_GE_CH_18_60_Li_Solo_SPK9.indb 17 Anl_GE_CH_18_60_Li_Solo_SPK9.indb 17
...................... 81 dB (A)
pA
.......................... 91 dB (A)
........ 96 dB(A)
WA
2
2
- 17 -
GB
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.

5. Before starting the equipment

The equipment is supplied without batteries
and without a charger.
Assembly of the steady grip
Push on the steady grip (Fig. 2 / item 3) in the di-
rection of the arrow as shown in Fig. 4a.
Make sure that the electrical contacts are
connected correctly.
Then tighten the screws (Fig. 4b / item 9).
Rotatable handle
The hedge trimmer is fi tted with a rotatable rear
handle. It can be rotated 90° to the left and right.
To do this, pull the slide (Fig. 13 / item 5) in the
direction of the arrow and rotate the handle.
To return the handle to its original position, pull
the slide (Fig. 13 / item 5) back in the direction of
the arrow. The handle should be rotated through
90° when performing vertical cuts.
Fitting the cuttings collector (Fig. 5a-5c)
For horizontal cutting we recommend that you
install the cuttings collector. This enables you to
remove the cuttings easily and keep the top of
the hedge clear (Fig. 5a/5b). Position the cuttings
collector (6) on the cutter rail (Fig. 5c). Then slide
the cuttings collector toward the tip of the cutter
rail to clamp it fi rmly under the retaining pin (Fig.
5c / item A).
Installing the battery (Fig. 4c)
Press the push/lock button of the battery pack as
shown in Fig. 4c and slide the battery pack into
the mount provided. Make sure that the push/lock
button engages properly. To remove the battery
pack, follow the steps in reverse order.
07.04.2021 14:14:36 07.04.2021 14:14:36