Noise/Vibration Information; Declaration Of Conformity - Bosch PMF Universal Manual Original

OBJ_BUCH-2472-003.book Page 14 Monday, November 16, 2015 12:29 PM
14 | English

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-4.
Typically the A-weighted noise levels of the product are:
Sound pressure level 86 dB(A); Sound power level 97 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Sanding: a =3.5 m/s , K=1.5 m/s
h
Cutting with plunge cut saw blade: a
2
K=1.5 m/s
Cutting with segmental saw blade: a
2
Scraping: a =12 m/s , K=1.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
Selecting the Application Tool/Accessory
The following table shows examples for application tools. Further application tools can be found in the extensive Bosch acces-
sories program.
Accessory
BIM segment saw
blade
Base plate for sand-
ing, series Delta
93 mm
HCS plunge cut saw
blade, wood
HCS plunge cut saw
blades, wood
1 609 92A 1PP | (16.11.15)
accessories, keep the hands warm, organisation of work pat-
terns.

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards:
2
EN 60745-1, EN 60745-2-4, EN 50581.
2
=12.5 m/s ,
h Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ETM9,
2 2
=14 m/s , K=2.5 m/s
h 70538 Stuttgart, GERMANY
2
.
Henk Becker
Executive Vice President
Engineering
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Assembly
Changing the Tool
 Before any work on the machine itself, pull the mains
plug.
 Wear protective gloves when changing application
tools/accessories. Contact with the application tool/ac-
cessory can lead to injuries.
Material Application
Wooden materials, plas- Separating and plunge cuts; also for sawing close to edges,
tic, non-ferrous metals in corners and hard to reach areas;
example: shortening already installed bottom rails or door
hinges, plunge cuts for adjusting floor panels
Depends on sanding sheet Sanding surfaces close to edges, in corners or hard to reach
areas;
depending on the sanding sheet for, e.g., sanding wood,
paint, varnish, stone
Wooden materials, soft Separating and deep plunge cuts; also for sawing close to
plastics edges, in corners and hard to reach areas;
example: narrow plunge cut in solid wood for installing a
ventilation grid
Wooden materials, soft Smaller separating and plunge cuts;
plastics example: cut-outs in furniture for cable connections
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Bosch Power Tools