Makita DWT310 Manual De Instrucciones página 8

Hook
CAUTION:
Be sure to attach the shoulder belt
included in the tool as the standard accessory.
Use the shoulder belt for carrying the tool, and
never use the hook for other purposes such as
the fall prevention at high location. I f t h e h ook is
used for other purposes, excessive load may break
them and cause serious injury to the operator and
person around/underneath the operator.
CAUTION:
When you attach the shoulder
belt to the hook, be sure to attach it securely. I f it
is attached incompletely, the tool may come off and
cause an injury.
CAUTION:
When carrying the tool using
the shoulder belt, be careful not to entangle the
shoulder belt w ith your body or objects and not to
hit objects w ith the tool. Failure to do so may cause
an a c c i d ent.
CAUTION:
Remove the shoulder belt from
the hook before operating the tool. Failure to do
so may lose your balance at operation and cause an
a c c i d ent.
Fig.6: 1. H ook 2. Shoulder belt
Attach the shoulder belt included in the tool as the
standard accessory to the hook for carrying the tool.
Remove the shoulder belt from the hook before operat-
ing t h e tool.
ASSEMBLY
CAUTION:
Al w ays be sure that the tool is
s w itched off and the battery cartridge is removed
before carrying out any w ork on the tool.
Removing the outer and inner
sleeves
CAUTION:
Be careful not to allo w foreign mat-
ter to enter the insides of the tool w hen removing
or installing the outer and inner sleeves.
1. L oosen t h e t w o s c re w s w h ile h ol d ing t h e outer
sleeve. The outer and inner sleeves will be pushed up
by the springs built into the tool.
Fig.7: 1. O uter slee v e 2. S c re w
2. P ress t h e pin d o w n to remo v e t h e inner slee v e
f rom t h e outer slee v e.
Fig.8: 1. I nner slee v e 2. P in 3. O uter slee v e
NOTICE:
Be careful not to drop the inner sleeve
w hen removing it.
NOTICE:
Do not remove the tip rod, tip rod
spring, and inner sleeve spring from the tool.
Fig.9: 1. T ip ro d 2. T ip ro d spring 3. I nner slee v e
spring
Installing the outer and inner
sleeves
P la c e t h e inner slee v e w it h t h e pin f a c ing up w ar d .
Attach the outer sleeve to the inner sleeve securely
w h ile pressing t h e pin o f t h e inner slee v e.
Fig.10: 1. O uter slee v e 2. P in 3. I nner slee v e
I nsert t h e outer an d inner slee v es into t h e tool w h ile
rotating t h e inner slee v e c lo c k w ise an d c ounter c lo c k-
w ise until t h e outer slee v e tou c h es t h e tool. T ig h ten t h e
two screws firmly.
Fig.11: 1. O uter slee v e 2. S c re w
NOTICE:
Make sure that there is no gap bet w een
the outer sleeve and the tool.
OPERATION
CAUTION:
Al w ays insert the battery cartridge
all the w ay until it locks in place. If you can see the
red indicator on the upper side of the button, it is not
locked completely. Insert it fully until the red indicator
cannot be seen. If not, it may accidentally fall out of
the tool, causing injury to you or someone around
you.
CAUTION:
Keep the bolt tips off of the
ground, oor, walkways, etc. to prevent injury
from tripping or falling.
1. Tighten bolts preliminarily by using a hand wrench.
2. Hold the tool firmly and place the inner sleeve over
the bolt so that the inner sleeve completely covers the
bolt tip.
Fig.12: 1. I nner slee v e 2. Bolt tip
NOTICE:
Be careful when fitting the sleeve onto
the bolt tip. S triking t h e tip c an d amage it so t h at it
will no longer fit inside the sleeve properly.
3. Push the tool lightly until the outer sleeve com-
pletely hold the nut. If the outer sleeve fails to hold the
nut, rotate t h e tool c lo c k w ise or c ounter c lo c k w ise w h ile
pushing the tool lightly.
4.
Press the trigger-lock button, and then pull the
s w it c h trigger. T h e outer slee v e rotates to tig h ten t h e
nut.
Fig.13: 1. O uter slee v e 2. Nut
NOTICE:
Do not force the tool do w n excessively.
Apply the do w n w ard force to the degree needed
to stabilize the tool.
5. When the specified torque is attained, the bolt
tip will be sheared at its notched portion. The bolt tip
remains insi d e t h e inner slee v e.
Fig.14: 1. Not c h e d portion 2. Bolt tip
6. R elease t h e s w it c h trigger an d w it h d ra w t h e tool in
a straig h t line.
Fig.15: 1. O uter slee v e
8 ENGLISH