Kalorik TKG HA 1002 Manual De Instrucciones página 14

Fax +32 2 359 95 50

 Put the appliance on a stable level surface.
 Make sure that the appliance is in "OFF" position, and that the appliance is unplugged.
 Fill the stainless steel bowl with the chosen ingredients.
 Press the release lever of the bracket down and place the bracket in vertical position.
 Place the stainless steel bowl on the base and turn it clockwise to lock it in place (see
page 5, figure C).
 Make sure that the bowl cover is in place on the bracket. If not, mount it onto the bracket
making sure that the lug of the bowl cover enters into the slot of the bracket and turn the
bowl cover clockwise to lock it in place (see page 5, figure D).
 Insert the beater, dough hook or whisk onto the axis of the bracket making sure that the
lugs of the axis enter into the slots of the accessory and turn the accessory clockwise until
it locks in place (see page 5, figure E).
 Check if the accessory is locked properly by pulling it gently.
 Press the release lever of the bracket in order to put the bracket back in horizontal position
so that the accessory is immersed in the bowl. Make sure that the bowl cover fits onto the
bowl.
 Plug in the appliance and select the desired speed. For the dough hook (e.g. to make
dough for cake or biscuits) we recommend speed 1 or 2, for the beater (e.g. for dry
ingredients such as butter, potatoes and flour) we recommend speed 3 or 4 and for the
whisk (e.g. for egg white or whipped cream) we recommend speed 5.
 The position "P" (Pulse) is particular because the button has to be held manually. If you
release it, the appliance stops.
 During use you can add ingredients through the opening of the bowl cover.
 When the preparation is ready, press the OFF key to switch off the appliance and unplug
it.
 Press down the release lever of the bracket and place the bracket in vertical position.
Remove the accessory and the bowl cover turning them anticlockwise (see page 5,
figures F and G).
 Turn the stainless steel bowl anticlockwise and take it off the base (see page 5, figure H).
MOUNTING AND USE OF THE BLENDER
For safety reasons the glass blender jug and its plastic base are fixed and cannot be
separated. Therefore never try to unscrew the plastic base for cleaning or for any other
purpose.
 Remove the top protection cover from the appliance (see page 6, figure I).
 Put the pouring jug onto the motor block, turn it slightly clockwise to lock it into place and
make sure it is correctly inserted (see page 6, figure J).
 Remove the lid of the blender.
 Fill the pouring jug with the chosen ingredients.
 Put the lid on the pouring jug. Close the feeding hole of the lid with the cap. Make sure
the two small lugs of the lid enter into the two small slots of the cap and turn the cap
clockwise to lock it into place.
 Plug in the appliance.
 Choose the mixing speed with the control panel. Position OFF corresponds to stopping the
appliance, position 1 to a slow speed and position 5 to a fast speed.
 Position "P" (Pulse) is particular because the button has to be kept manually. This position is
generally used to crush ice in order to avoid damages on the blades, but it can also be
used to complete the mixing.
 It is also possible to add liquids or other ingredients anytime without stopping the
appliance. You only have to remove the cap which closes the feeding opening by turning
it anticlockwise and lifting it straight up.
All manuals and user guides at all-guides.com
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International BELGIUM. The pages must be reproduced
and folded in order to obtain a booklet A5 (+/- 148.5 mm
width x 210 mm height). When folding, make sure you
keep the good numbering when you turn the pages of
the I/B. Don't change the page numbering. Keep the
language integrity.
14
Assembly page 14/52
TKG HA 1002 - 140312