Mopar 82206761 Instrucciones De Instalación

KIT CONTENTS:
1 Cargo Liner
4 Fastener Clips
2 Stretch Cords
1 Instruction Sheet
TOOLS REQUIRED:
Utility knife (if cutouts are to be removed)
TO INSTALL:
1. Remove Cargo Liner from box. NOTE: Your Cargo
Liner is rolled up for packaging purposes. It must be
removed from the box and allowed to relax before
installation in your vehicle. Lay flat at room
0
temperature (70 F) for approximately 1 hour for the
Cargo Liner to relax for installation. Warmer
temperatures will allow the material to relax faster,
while colder temperatures will slow the process
considerably.
2. To install in vehicle, put back seats in lowered
(flat) position. Place Cargo Liner into vehicle,
pushing the Liner into the contours of the cargo area
of your vehicle.
3. Now return rear seat to upright position. Fold top
flap under Cargo Liner on seat back (see Figures 4 &
5). Attach one end of Stretch Cord into keyhole slot.
Position Stretch Cord around headrest supports and
fasten other end of Stretch Cord in next keyhole slot
(see Figure 3). Continue to other side of Cargo Liner
and fasten in the same manner.
4. Refer to Figures 4 & 5 to see how Fastener Clips
are used and how they are to be positioned.
5. When putting on the Clips that go around the side
of the folded Liner, position them about 1" down from
the fold. With the Clips positioned on the Liner, push
the velcro-backed Clips against the carpeting on the
seat backs — wiggle and push on the fastener to
securely attach it to the carpeting (see Figure 4).
NOTE: The Fastener Clips are designed to stay in
place on the seat backs.
6. Before lowering the seats,unhook stretch cords.
The Liner will slide out of the Fastener Clips. Unfold
the top flap to allow the liner to lay flat. To raise, pull
the seats up and fold the Liner at the top hinge.
Insert the folded Liner into the Clips by pulling the
Clips open and inserting the folded Liner into the
Clips (see Figure 5).
CARE OF LINER:
Clean Liner with damp cloth or, if excessively dirty,
remove the Liner from the vehicle, brush with mild
soap and water, rinse and let dry before reinstalling.
PRINTED IN USA
CARGO LINER INSTALLATION INSTRUCTIONS
1-800-OE-LINER IN USA, MONDAY - FRIDAY, 7AM - 5:30PM CENTRAL TIME,
1-800-343-2469 IN CANADA, MONDAY - FRIDAY, 7AM - 4:30PM CENTRAL TIME
PA0806 (10/18/01)
PART NO. 82206761
Jeep Liberty (KJ), 2001
FOR TECHNICAL ASSISTANCE, CALL:
FIGURE 1
FIGURE 2
FASTENER
CLIPS
FIGURE 3
JEEP CHEROKEE
USES 4 CLIPS & 2
STRETCH CORDS.
SEAT BACK
FIGURE 4
BACK SEAT
FOLD
SMALL
FLAPS
UNDER
SLIDE CLIPS ONTO
FOLDED FLAPS, THEN
PUSH CLIPS INTO CARPET
AS SHOWN.
FIGURE 5
WHEN FOLDING
SEATS DOWN:
CLIPS STAY ATTACHED TO SEAT BACKS
WHEN FOLDING
SEATS UP:
FOLD FLAP UNDER
TEXTURED SIDE UP WHEN
INSTALLED IN VEHICLE
HEADREST
STRETCH
CORDS
STRETCH CORD
KEYHOLE
OPENING
SEAT BACK LINER
1"
1
PUSH FASTENER CLIP ONTO CARPET
1
ON SEAT BACK.
WIGGLE CLIP BACK & FORTH WHILE
2
PUSHING INTO CARPETING TO
SECURELY ATTACH CLIP IN PLACE
UNFOLD FLAP TO COMPLETELY
COVER SEAT BACK
INSERT LINER
INTO CLIPS AS
1 PULL FASTENER CLIP OPEN
(DO NOT OVERBEND).
SHOWN AT RIGHT
PUSH FOLDED FLAPS INTO
2
CLIP AND LET CLIP GO.
CLIPS HOLD LINER UP
3
AGAINST SEAT BACKS.
2
2
3