Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 9
Safety
These instructions are for your safety. Please read through
them thoroughly prior to installation and retain them for future
Safety
reference.
These instructions are for your safety. Please read through
accordance with local regulations (IET wiring regulation
them thoroughly prior to installation and retain them for future
BS7671).
reference.
Check the pack and make sure you have all of the parts listed.
Remove all packaging, wrap etc. from the product.
accordance with local regulations (IET wiring regulation
Decide on the appropriate location for your product.
BS7671).
Check the pack and make sure you have all of the parts listed.
using the screws and wall plugs supplied. The screws and wall
Remove all packaging, wrap etc. from the product.
Decide on the appropriate location for your product.
supplied and must be purchased.
Take care not to drill into any pipes or mains cables beneath the
using the screws and wall plugs supplied. The screws and wall
surface during mounting holes preparation.
supplied and must be purchased.
Take care not to drill into any pipes or mains cables beneath the
It is always recommended to cut the hole slightly smaller than
surface during mounting holes preparation.
We recommend connecting this product to an external / wall
It is always recommended to cut the hole slightly smaller than
switch in order to deactivate the motion detection function if
necessary.
Wiring diagram is for reference only. Always refer to the terminal
We recommend connecting this product to an external / wall
marking for wiring. Ensure that all electrical connections are tight
switch in order to deactivate the motion detection function if
and that no loose strands are left out of the terminal block.
necessary.
When the product does not light after installation:
Wiring diagram is for reference only. Always refer to the terminal
> Ensure there is no electricity failure
marking for wiring. Ensure that all electrical connections are tight
> Ensure all the connections are secured
and that no loose strands are left out of the terminal block.
If you have any doubt about installation / use of this product,
When the product does not light after installation:
> Ensure there is no electricity failure
It is recommended to have a regular schedule of care and
> Ensure all the connections are secured
maintenance to keep the surface condition well.
If you have any doubt about installation / use of this product,
It is recommended to have a regular schedule of care and
maintenance to keep the surface condition well.
Warranty Period and Conditions
At Blooma, we devote special attention to selecting high-quality materials and use manufacturing techniques that enable us to create
designer and durable product ranges.
Warranty Period and Conditions
That is why we offer a 2-year warranty against product manufacturing defects.
This product is under warranty for 2 years as from the date of purchase, for normal, non-professional household use. The warranty shall only
At Blooma, we devote special attention to selecting high-quality materials and use manufacturing techniques that enable us to create
apply upon presentation of the till receipt or the invoice. Keep your proof of purchase in a safe place.
designer and durable product ranges.
The warranty covers product breakdowns and malfunctions under the condition that the product is used in accordance with its intended
That is why we offer a 2-year warranty against product manufacturing defects.
use and subject to installation and maintenance in accordance with good practice and the information contained in the user's manual. This
This product is under warranty for 2 years as from the date of purchase, for normal, non-professional household use. The warranty shall only
product must be installed so that it may be later removed without damaging it.
apply upon presentation of the till receipt or the invoice. Keep your proof of purchase in a safe place.
This contractual warranty does not cover defects and damage caused by the natural wear of parts, bad weather
The warranty covers product breakdowns and malfunctions under the condition that the product is used in accordance with its intended
freezing, damage caused by water quality (hardness, aggressiveness, corrosion, etc.), by the presence of foreign bodies transported by
use and subject to installation and maintenance in accordance with good practice and the information contained in the user's manual. This
product must be installed so that it may be later removed without damaging it.
negligence, accident or maintenance that is defective or does not comply with good practice or the information in the user's manual.
This contractual warranty does not cover defects and damage caused by the natural wear of parts, bad weather
The following are also excluded from the warranty: harmful consequences due to the use of accessories and/or non-original equipment
freezing, damage caused by water quality (hardness, aggressiveness, corrosion, etc.), by the presence of foreign bodies transported by
The warranty is limited to those parts recognised as defective. Under no circumstances shall it cover fringe expenses (travel, labour) and
negligence, accident or maintenance that is defective or does not comply with good practice or the information in the user's manual.
direct and consequential damage.
The following are also excluded from the warranty: harmful consequences due to the use of accessories and/or non-original equipment
This guarantee is in addition to and does not affect your statutory rights.
The warranty is limited to those parts recognised as defective. Under no circumstances shall it cover fringe expenses (travel, labour) and
direct and consequential damage.
This guarantee is in addition to and does not affect your statutory rights.
3663602893592-Blooma-A5-IM-V04.indb 3

Technical Data

1000 W for incandescent
Max. switching
Technical Data
capacity:
250 W for LED
This product complies with conformity
1000 W for incandescent
Conformity with all relevant EC Directive
Max. switching
requirements of the applicable European
requirements.
capacity:
Regulations or Directives.
250 W for LED
IP20
This product complies with conformity
Conformity with all relevant EC Directive
requirements of the applicable UK
requirements.
IP44
Regulations.
Splash-proof.
IP20
Waste electrical products should not be
disposed of with household waste. Please
IP44
recycle where facilities exist. Check with
Splash-proof.
your Local Authority or local store for
Waste electrical products should not be
recycling advice.
disposed of with household waste. Please
recycle where facilities exist. Check with
This product is not suitable for dimming.
your Local Authority or local store for
recycling advice.
xxWyy
xx-year; yy-week of the year
This product is not suitable for dimming.
xxWyy
xx-year; yy-week of the year
15/11/2017 10:05

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

3663602893592

Tabla de contenido