EN User Manual
SAT Finder with mechanical display | SAT Finder with digital display
Saftey Instructions
• Read the user manual completely and carefully before use.
It is part of the product and contains important information for correct use.
• Keep this manual.
It must be available for uncertainties and passing the product.
Product
• Keep yourself safe at the product's set-up location
(i.e., watch out for slippery rooves, danger of falling)
• Install the system and devices attached to it in a way that persons cannot be
injured, or objects not be damaged for example by dropping or
•
Do not use the device directly in front of the dish to avoid a wrong signal.
• Use a 5dB attenuator in the case of a LNB gain higher than 60dB.
• Do not place any objects on the device.
• Do not install the product close to openings of air conditioners, or at places with
an excessive amount of dust or smoke.
• Do not modify or alter product nor accessories.
Not meant for children. The product is not a toy!
• Secure
packaging, small parts and insulation against accidental use.
• Avoid stresses such as heat and cold, moisture and direct sunlight,
vibration and mechanical pressure.
• In case of questions, defects, mechanical damage, trouble and other
problems, non-recoverable by the documentation, contact your dealer or
producer.
• Do not permanently install device between the satellite dish and the receiver!
Continuous operation can damage the product.
• NEVER leave unattended while in operation.
• For industrial facilities, the accident prevention regulations of the
Health and Safety Executive for electrical systems and equipment must be
observed.
• Please also observe the safety instructions and operating instructions
of the other devices connected to the product.
• Do not open the housing.
• For questions, defects, mechanical damages, malfunctions, and other
functional problems which cannot be resolved by this guide, please contact
your dealer or producer.
• Only use in dry ambience.
Risk of injury by stumbling and falling.
Description and Function
SAT Finder
This product is used to align your satellite dish for optimal reception. The SAT
Finder shows the signal strength of the satellite in the display. The Model 67000
has an illuminated display. The Model 67140 has an illuminated LCD display with
digital indication of the field strength of the satellite signal and additionally
generates an acoustic signal, which gets louder the better the signal is.
Scope of Delivery
Article-No.
Scope of Delivery
67000
SAT FINDER analogue, F-connection cable, User
manual
67140
SAT FINDER with digital LCD, F-connection cable , User
manual
REV2019-11-13
V2.3ir
Subject to change without notice.
All manuals and user guides at all-guides.com
Controls and Parts
67000
1 Connection to LNB
3 Connection to SAT receiver
5 Tension indicator
67140
1 Connection to the LNB
3 Compass
5 Light
7
ATT: Signal amplification of the input signal
8 LCD Display
Intended Use
stumbling.
We do not permit using the device in other ways like described in chapter
"Description or Function" and "Safety Instructions". Not attending to these
regulations and safety instructions might cause fatal accidents, injuries, and
damages to persons and
Preparing
• Check the scope of delivery for completeness and integrity.
Connection and Operating
1.
Connect the coaxial cable coming from LNB to the satellite socket
(1) of the SAT Finder.
2.
Connect the coaxial cable of the receiver input to the receiver
connector (2) of the SAT Finder.
3.
Switch on the SAT receiver. The SAT Finder starts automatically
because it is powered by the SAT Receiver.
4.
Align your satellite dish with the approximate azimuth angle
(horizontal angle) and the approximate elevation angle (elevation
angle).
Only 67140:
5.
Turn the volume control (9) fully to until a maximum signal strength
is displayed.
6.
Increase the signal by slowly moving the satellite dish
horizontally and vertically. The higher the display, the better the
signal.
When the SAT Finder receives the full signal, you can fine tune the signal
strength setting (4) on the Model 67000 or press the
Model 67140 to reduce the input signal.
7.
Move the satellite dish again to the largest possible display and the
loudest beep.
67000 and 67140
8.
Amplify the input signal with the Model 67000 signal strength setting
or the Model 67140
9.
After adjustment, disconnect the product from the LNB and receiver.
10.
Reconnect the LBN to the SAT receiver after alignment.
2 Analogue display
4 Signal strength adjustment
6 Frequency indicator
2 Connection to the SAT Receiver
4 Buzzer control
6
ATT: Signal reduction of the input
Signal
9 Volume: Signal Volume Control
property.
ATT button (6) on the
ATT button if it is too weak.
Maintenance and Cleaning
The products are maintenance-free.
• Clean only with a dry, soft cloth.
• Do not use cleaning agents and chemicals.
• Store cool and dry.
• Store the product out the reach of children and in a dry and dust-
protected ambience when not in use.
• Keep and use the original packaging for transport.
Disposal Instructions
According to the European WEEE directive, electrical and electronic
equipment must not be disposed with consumers waste. Its
components must be recycled or disposed apart from each other.
Otherwise contaminative and hazardous substances can pollute our
environment.
As a consumer, you are committed by law to dispose electrical and electronic
devices to the producer, the dealer, or public collecting points at the end of the
devices lifetime for free. Particulars are regulated in national right. The symbol
on the product, in the user manual, or at the packaging alludes to these terms.
With this kind of waste separation, application, and waste disposal of used
devices you achieve an important share to environmental protection.
WEEE No: 82898622
Packaging
Packaging can be disposed of free of charge at the suitable
collection points – paper belongs in paper bins, plastics belong in
yellow sacks and glass belongs in used glass bins.
DE4535302615620
Goobay® | by Wentronic GmbH
Pillmannstraße 12 | 38112 Braunschweig
Germany