Technical Data; Noise Information - Bosch GCM 18V-305 GDC Professional Manual Original

(54) Hex socket screw for mounting the saw blade
(55) Clamping flange
(56) Inner clamping flange
(57) Clamping lever of the saw table extension
(58) Locking screw for the adjustable fence
(59) Damper
(60) Set screws for damping
(61) Holes for screw clamp
(62) Wing bolt
(63) Threaded rod
(64) Angle indicator for mitre angles
(65) On/off switch
(66) Screws for insert plate
(67) Clamping screw for length stop
(68) Set screws for positioning the laser (flush align-
ment)
(69)/ Set screws for 0° basic setting (bevel angle)
(70)/
(71)
(72) Set screw for 45° basic setting (left-hand bevel
angle)
(73) Set screw for 45° basic setting (right-hand bevel
angle)
(74) Set screws for mitre angle scale
(75) Screw for mitre angle indicator
(76) Set screw for adjusting the clamping force of the
clamping handle for any bevel angle
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical Data

Sliding mitre saw
Article number
Rated voltage
A)
No-load speed
A)
No-load speed in ECO mode
Laser type
Laser class
Divergence of laser line
Weight according to EPTA-Pro-
B)
cedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperature
C)
during operation and during
storage
Bosch Power Tools
Sliding mitre saw
Recommended rechargeable
batteries
Recommended chargers
Data transmission
Bluetooth
Signal interval
Max. signal range
Dimensions of suitable saw blades
Saw blade diameter
Base blade thickness
Max. cutting width
Hole diameter
A) Measured at 20–25 °C with rechargeable battery ProCORE18V
B) Depends on battery in use
C) Limited performance at temperatures <0 °C
D) The mobile terminal devices must be compatible with Bluetooth
E) The signal range may vary greatly depending on external condi-
Permitted workpiece dimensions (maximum/minimum): (see "Per-
missible workpiece dimensions", page 28)

Noise Information

Noise emission values determined according to
EN 62841-3-9.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 93 dB(A); sound power level
106 dB(A). Uncertainty K = 3 dB.
GCM 18V-305 GDC
Wear hearing protection!
3 601 M43 0..
The noise emission value given in these instructions has
V= 18
been measured in accordance with a standardised measur-
-1
min 3000−4000
ing procedure and may be used to compare power tools. It
-1
min 2550 may also be used for a preliminary estimation of noise emis-
sions.
nm 650
The noise emission value given represents the main applica-
mW < 1
tions of the power tool. However, if the power tool is used
1M
for other applications, with different application tools or is
poorly maintained, the noise emission value may differ. This
mrad 1.0
may significantly increase noise emissions over the total
(full
working period.
angle)
To estimate noise emissions accurately, the times when the
kg 26.9−27.8
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
°C 0 to +35
ficantly reduce noise emissions over the total working
period.
°C –20 to +50
®
E)
8.0Ah.
Low Energy devices (version 4.2) and support the Generic Ac-
cess Profile (GAP).
tions, including the receiving device used. The Bluetooth® range
may be significantly weaker inside closed rooms and through
metallic barriers (e.g. walls, shelving units, cases, etc.).
1 609 92A 6TT | (19.07.2021)
English | 21
GCM 18V-305 GDC
GBA 18V...
ProCORE18V...
GAL 18...
GAX 18...
GAL 36...
®
Bluetooth 4.2
D)
(Low Energy)
s 8
m 30
mm 305
mm 1.7–2.6
mm 3.2
mm 30
®