Becken BDM2741 HP Manual De Instrucciones página 6

Transport
Be cautious. Do not grasp any salient parts of the machine. The machine door cannot
be used as a support during transport. If the dryer can't be transported in an upright
position, it can be slanted at just under 30°.
Installation Position
1. For your convenience, it is recommended that the machine is positioned
close to your washing machine.
2. The tumble dryer must be installed in a clean place, where dirt does not build
up. Air must be able to circulate freely all around the appliance. Do not obstruct
the frontal air inlet or the air intake grills at the back of the machine.
3. To keep noise and vibration to a minimum when the dryer is in use, it should
be placed on a firm and level surface.
4. The feet must never be removed. Do not restrict the floor clearance through
deep pile carpets, strips of wood or similar. This might cause heat built-up which
will interfere with the appliance's operation.
Ensuring the dryer is level
Once in its permanent operating position, check that
the dryer is absolutely level with the aid of a spirit level.
If it is not, adjust the feet with a tool.
Power Supply Connection
1. Make sure that the power supply voltage is the same as the electric
specification of the dryer.
2. Do not connect the dryer to a power extension, a universal plug or socket.
Warnings
! Let the dryer stand for 2 hours after transport (BDM2741 HP only).
Before first use, please use a piece of soft fabric to clean the inside of the drum.
a) Put some clean rags into the drum.
b) Plug in the power cord, press [On/Off].
c) Select the [Refresh] Programme, press the [Start/Pause] button.
d) After finishing this programme, please follow the "cleaning and routine maintenance"
instructions (refer to page 16) to clean the filter door.
! During drying, the compressor and the water pump generate some noise which is
entirely normal (BDM2741 HP only).
10
Advice
1. Before drying, thoroughly spin the laundry in the washing machine. High spin
speed can reduce the drying time and reduce energy consumption.
2. For a uniform drying result, sort the laundry according to fabric type and
drying programme.
3. Before drying, please close zips, hooks and eyelets, do up any buttons, tie
fabric belts, etc.
4. Do not over dry the clothes, because over dried clothes can easily get creases
or shrink.
5. Do not dry articles containing rubber or similar elastic materials such as
raincoats, bicycle covers, etc.
6. The door must only be opened after the drying programme is over. Do not
open the door before the programme finishes to avoid scalding yourself with
hot steam or on the drying machine itself.
7. Clean the lint filter and empty the condensed water container after each use
to avoid extended drying time and additional energy consumption.
8. The reference weight of dry clothes
Mixed-fabric coats Jacket
(about 800 g) (about 800 g, cotton)
Single Sheets Work Clothes
(about 600 g, cotton) (upper and lower)
(about 1120 g in cotton)
Short sleeve shirts Underpants
(about 180g in cotton) (about 70 g, cotton)
Select the programme
1. Press the [On/Off] button. When the working state LED lights up, rotate the
programme knob to select the desired programme.
2. Select the [Delay], or [Anti-Crease] functions for additional options.
3. Press the [Start/Pause] button.
Start of the Programme
The drum will keep rotating after the start of the programme, and the working state
LED will flash in sequence.
Note:
Occasionally, the drum might suspend for about 40 seconds during the drying
procedure, but the working state LED flashes normally. The dryer is automatically
adjusted during this time and will continue operating.
Tumble Dryer | Secadora | Máquina de Secar Roupa
Jeans Trousers Towel Quilts
(about 800 g) (about 900 g, cotton)
Pyjamas Long sleeve shirts
(about 200 g) (about 300g in cotton)
Socks
(about 30 g, mixed
weave)
EN
11