Before Use; During Use; After Use - Skil 6950 Manual Original

e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SAFETY INSTRUCTIONS FOR IMPACT DRILLS
GENERAL
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
• This tool should not be used by people under the age of
16 years
• Do not work materials containing asbestos (asbestos
is considered carcinogenic)
• Never use the tool when cord is damaged; have it
replaced by a qualified person
• Always disconnect plug from power source before
making any adjustment or changing any accessory
ACCESSORIES
• SKIL can assure flawless functioning of the tool only
when original accessories are used
• Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool

BEFORE USE

• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
• Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
• Use suitable detectors to find hidden utility lines or
call the local utility company for assistance (contact
with electric lines can lead to fire or electrical shock;
damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
• Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
• Certain kinds of dust are classified as carcinogenic (such
as oak and beech dust) especially in conjunction with
additives for wood conditioning; wear a dust mask and
All manuals and user guides at all-guides.com
• Follow the dust-related national requirements for the

DURING USE

• Wear ear protectors when impact drilling (exposure
• Use auxiliary handle(s), if supplied with the tool
• Hold power tool by insulated gripping surfaces,
• Always keep the cord away from moving parts of the tool
• In case of electrical or mechanical malfunction,
• If the cord is damaged or cut through while working, do
• If the drill bit becomes unexpectedly jammed (causing a
• Be aware of the forces that occur as a result of jamming

AFTER USE

• When you put away the tool, switch off the motor and
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
• If for any reason the old plug is cut off the cord of this tool,
USE
• On/off 4
• Switch locking for continuous use 5
• Speed control for smooth starting 6
• Changing direction of rotation 7
• Changing bits 8
• Selecting operating mode 9
9
work with a dust extraction device when
connectable
materials you want to work with
to noise can cause hearing loss)
(loss of control can cause personal injury)
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord (a cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock)
immediately switch off the tool and disconnect the plug
not touch the cord, but immediately disconnect the plug
sudden, dangerous reaction), immediately switch off the
tool
(especially when drilling metals); always use auxiliary
handle G 2 and take a secure stance
ensure that all moving parts have come to a complete
standstill
in the cord of this tool to the earth terminal of the plug
it must be disposed of safely and not left unattended
- when not properly set in left/right position, switch A
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
- turn switch D to "changing bits" until it snaplocks (only
activate when tool is switched off and plug is
disconnected)
- insert the bit as deep as possible in the chuck
- once the chuck produces a clicking sound, bit is
mounted correctly
! do not use damaged bits
! never start drilling with switch D set for
"changing bits", as this could damage the tool
- turn switch D to the desired operating mode until it
snap-locks
1 = normal drilling
2 = impact drilling
! select operating mode only when tool is switched
off and plug is disconnected