Black and Decker BDCMTI Manual De Instrucciones página 15

f Hold tool firmly with two hands. Loss of control
can cause personal injury.
f Wear safety goggles or other eye protection.
Hammering and drilling operations cause chips to fly.
Flying particles can cause permanent eye damage.
f Bits, sockets and tools get hot during operation.
Wear gloves when touching them.
f Do not operate this tool for long periods of time.
Vibration caused by tool action may be harmful to your
hands and arms. Use gloves to provide extra cushion
and limit exposure by taking frequent rest periods.
f Wear appropriate personal hearing protection
during use. Under some conditions and duration of
use, noise from this product may contribute to hearing
loss.
Warning! Impact wrenches are not torque wrenches.
Do not use this tool for tightening fasteners to specified
torques. An independent, calibrated torque measurement
device such as a torque wrench should be used when
under tightened or over tightened fasteners can lead to
the failure of the joint.
Warning! Always use safety glasses. Everyday
eyeglasses are not safety glasses. Also use face or dust
mask if drilling operation is dusty. Always wear certified
safety equipment:
f ANSI Z87.1 eye protection (CAN/CPA Z94.3),
f ANSI S12.6 (S3.19) hearing protection,
f NOSH/OSHA respiratory protection.
Warning! Always wear proper personal hearing
protection that conforms to ANSI S12.6 (S3.19) during
use. Under some conditions and duration of use, noise
from this product may contribute to hearing loss.
Warning! Some dust created by power sanding,
sawing, grinding, drilling, and other construction activities
contains chemicals known to the state of California to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
f lead from lead-based paints,
f crystalline silica from bricks and cement and other
masonry products, and
f arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that
are specially designed to filter out microscopic particles.
f Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
All manuals and user guides at all-guides.com
dust, which may cause serious and permanent respiratory
or other injury. Always use NOSH/OSHA approved
respiratory protection appropriate for the dust exposure.
Direct particles away from face and body
When using an extension cord, be sure to use one heavy
enough to carry the current your product will draw. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating. The following table
shows the correct size to use depending on cord length
and nameplate ampere rating. If in doubt, use the next
heavier gauge. The smaller the gauge number, the heavier
the cord.
OPERATING INSTRUCTIONS
should this product be used near water.
work piece or accessory immediately after operating the
tool. They can become very hot. Handle carefully. Always
allow accessories and work piece to cool before handling.
remove battery from tool or disconnect plug from power
source before making any adjustments or removing
or installing attachments or accessories. Remove any
accessory from the attachment before removing or
installing the attachment.
Note: Refer to Power Unit instruction manual before
operating this tool for all safety warnings and details on
installing and removing attachments.
ENGLISH • 15
construction activities. Wear protective clothing
and wash exposed areas with soap and water.
Allowing dust to get into your mouth, eyes, or lay
on the skin may promote absorption of harmful
chemicals.
Warning! Use of this tool can generate and/or disperse
Voltage
Total length of cord in meters (m)
(Volts)
120-127V 0-7 7-15
220V 0-15 15-30
Rated
Minimal cross-sectional area of the
Ampere
cord in milimeters (mm
Range
0-6A 1,0 1,5
6-10A 1,0 1,5
10-12A 1,5 1,5
12-16A 2,5 4,0
Warning! Shock hazard. Under no circumstances
Warning! Risk of lacerations or burns. Do not touch
Warning! To reduce the risk of injury, turn off and
15-30 30-50
30-60 60-100
)
2
1,5 2,5
2,5 4,0
2,5 4,0
Not recommended